answersLogoWhite

0


Best Answer

I have read your question several times an don't quite understand it. Do you have cracks or joints below the skimmer line? Hmmm. Just raise the water level until the water is at about the halfway point on the throat of the skimmer. It may be that your skimmer is installed too high. Don't know - would have to see situation.

Ken

After reading the original question posed I have a better understanding of the problem. Whoever changed the question didn't know what they were talking about. It appears, by the 1st question that you have some sort of problem getting water to the pump. As above, maintain water level at middle of skimmer. You may have to add water manually to the pump pot by removing the pump lid and adding water to fill the pot. Replace the lid and start the pump. It may take a couple of minutes for water to start flowing. As water flow increases, release the air entrapped in the filter, via the air relief valve at the top of the filter tank. Now, you have a "primed" pump and a functioning pool.

User Avatar

Wiki User

16y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Will caulking the cement pool to the cool cement deck allow the pool to fill up more so the water can reach the basket and pump so it does not suck air?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What do shallow estuaries allow?

They allow sunlight to reach the benthos to power photosynthesis.


Poptropica special ingredient?

you have to go inside the temple and get past everything until you reach the basket that is the spcial ingredient


What are openings in the earth's crust that allow magma to reach the surface?

Volcanoes


Which type of soil would allow rainwater to reach the well faster and in greater amount?

Glacial till (sandy, gravelly) would allow rain water to reach a well faster and in greater quantities.


What are the factors affecting the initial setting time of cement?

When cement is mixed with water, it forms slurry which gradually becomes less plastic with the passage of time & finally a hard mass is obtained. In this process, at a certain stage when the cement paste is sufficiently rigid to withstand a definite amount of Pressure, it is said to have set & the time required to reach this stage is termed as "setting time".


Where is the comet medal in clockwork ruins galaxy?

In the 3rd section where the big cement wheels are rolling down the slope get on top of the wheel to reach it.


What states don't allow handguns in a car while travling?

They all do, they just don't all allow them to be loaded and/or within reach.


How do you you pump a balanced cement plug?

Balanced cement plug is pumped through drill string or open-ended tubing. 'Balanced Cement Plug' means that the top of cement outside the drillstring/ tubing will be the same height as the top of cement inside the drillstring at the end of pumping. The drillstring/ tubing is then slowly pulled from the wet cement, allowing the cement inside the string to fill the centre of the plug. There are lots of refinements in this method with open hole cement retainers or high viscosity 'cushions' often placed below cement. In vertical hole, most balanced plugs are successful. In extended reach wells, failure rates can be high with cement slumping and mixing with synthetic based muds. A typical checklist to improve cement plug success in extended reach wells would have: 1. Always use a tailpipe. This reduces the disruption to the plug caused by removal of the drillstring. 2. Clean up the hole thoroughly before pumping cement. Cement is an excellent hole cleaner. Many 'flash set' events reported are really packoffs caused by cement picking up a cuttings dune. 3. Put a diverter tool with BIG holes on the bottom of the tailpipe. This directs fluids up the hole during cementing 4. Use a scavenger spacer in front of the cement job to convert the formation from oil wet to water wet. 5. Slow down pumping to 1 BPM while displacing cement into open hole. This reduces mixing of cement and mud. 6. Put a cushion below the cement plug. A cement retainer is best. If a viscous cushion is spotted, weight the cushion to 1 ppg below the cement weight. 7. Gravity is NOT on your side. Cement can stay inside the tail pipe as you pull it from the plug. Pump the volume of cement inside the tailpipe as you pull the tailpipe from the plug. 8. Circulate clean the long way with the bottom of the tailpipe at the planned cement plug top.


Can you intercept ball on way to basket?

You can intecept the ball whenever you can as long as you don't foul them. If yuio don't push, reach or hit the player you can try to intercept it.


Which structures allow nutrients to reach the osteocytes from the blood vessels in the central canal?

osteoblast


Which type of concrete should you use when it must reach its design strength in about 28 days?

concrete made upof ordinary portland cement gain strength in 28days


What two processes allow energy generated in the sun to reach the outer layers?

Convection and radiation.