0
Wiring circuit for 240V welder with 3 prong plug pulling 6-3 wire do you need to replace welder cable with a 4 lead cable-plug or can you avoid the white lead to wire a 3 prong outlet red-black-green?
Wiki User
∙ 15y ago
It depends on the welder. If it doesn't need 120V you can just put a wire nut on the neutral and wire a 240V plug. If it needs 120/240V you need the 4 prong plug. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
If you do this work yourself, always turn off the power
at the breaker box/fuse panel BEFORE you attempt to do any work AND
always use an electrician's test meter having metal-tipped probes
(not a simple proximity voltage indicator)
to insure the circuit is, in fact, de-energized.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What would cause a short periodic low hum to come from a circuit breaker?
A bad circuit breaker. Replace it.
When did circuit breakers replace fuses in homes?
1950's
How do you reset circuit breakers in a Chrysler 1999 300M?
you have to replace them......they are not self resting.
What circuit breaker can you use to replace a Gould P1515?
Siemens type P, ITE as well
My circuit breaker keeps popping I have replace the 2-prong outlet with a 4-outlets and why is it still popping?
A breaker trips when there is too much current. If you unplug everything on the circuit and the breaker still trips then you have a wiring problem or a bad breaker. From your description it is not possible to be certain if the problem started when you installed new outlet or previously. You have to describe your problem in better detail to get a good answer. When you have a circuit that trips the corresponding breaker, you need to go through each outlet on the circuit and rule it out as the problem. This can be done by pulling each outlet, from the wall and systematically remove wires from outlets while power is off and determining when problem goes away.
What component can replace entire circuit?
Integrated circuit
What can be done to fix a pantech breakout when it wont charge or turn on?
It depends on what caused the device to not power on. The battery could be damaged. Replace the battery. The charging unit could be damaged. Replace the charging unit or find the damaged component and replace it. The charging connector could be damaged. Replace the circuit board or find the damaged component and replace it. The power button could be damaged. Replace the circuit board or find the damaged component and replace it. Something could have fried the circuit board. Replace the circuit board or find the damaged component and replace it.
Can you replace the heater core on a 1987 grand marquis with out pulling the dash?
no
Can you replace a crankshaft in a 1991 Geo Tracker without pulling engine?
No
What advantaged does a circuit breaker have compared with a fuse?
You can reset a circuit breaker but a fuse you must replace.
Can you replace a 2000 A Circuit breaker with 3150 A rating?
No.
What would cause a short periodic low hum to come from a circuit breaker?
A bad circuit breaker. Replace it.
When did circuit breakers replace fuses in homes?
1950's
What should I do if my diagnostics of my 1991 dodge stealth rt say that the fuel circuit is bad?
You should replace your fuel circuit..
How do you fix a short circuit in a 1997 Mercedes Benz c280?
The short circuit location can be found by a diagnostic tester. When the short circuit is located, replace the wiring or switch.
How do you fix obd11 code 446?
Replace the vent valve. Repair open, short, or resistance problem in the control circuit. Repair an open, or short, or resistance problem in the power circuit, or replace the PCM.
What should you do to the surge strip if the circuit breaker fails to reset?
You should replace the surge strip if the circuit breaker fails to reset.
