0
Your back turn signals and brake lights keep burning out the sockets are starting to melt a little you've replaced the bulbs 4 times - what is wrong?
Wiki User
∙ 17y ago
If it happens to be a Saturn LS, you might be able to get them replaced as part of a recall. If it's not a recall issue, replace the sockets and make sure you use some dielectric grease to keep the sockets from oxidizing and burning out. Sometimes the voltage regulator in your alternator can become faulty causing excess or lack of voltage. usually the lights are the first to notice, blown bulbs etc. I would recomend getting your alternator tested.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
Socket in World of Warcraft?
Items do have sockets in world of warcraft. They were added in The Burning Crusade expansion and you need a jewelcrafter to cut gems for the sockets.
Can a 168 pin dimm be replaced with a 184 pin dimm?
No. The sockets are different sizes.
What causes the brake lights not to work on a Chevy corsica and the turn signals not to work have changed flashers also relay?
Check bulbs they are double filamented smaller for brake/ turn signals Check the sockets for corrosion Check for power and ground to sockets Could be a problem in the steering column switch
What type of sockets are the most commonly used?
Metric 6 point sockets are the most commonly used sockets today. American made vehicle used to only have standard bolt, but today they are being replaced by metric bolts like all other manufacturers.
Why would my 1995 buick skylark lose brake lights or turn signals?
Check the bulbs - they are double filamented - smaller for stop/turn and larrger for tailights Check the sockets for corrosion Check the sockets for power /ground
How do you replace signal sockets in a 2002 Olsmobile Intrigue?
Did you mean turn signal sockets? Replacements can be bought with pigtail leads that can be spliced in, or OEM replacement parts may have an in-line connector. I haven't replaced any sockets on my Intrigue, so I can't speak from experience. Most of the sockets I have replaced were cracked or heat damaged, and they usually snap in or twist in to the bezel or housing. Be careful to first observe how the socket is mounted as the all-plastic parts on cars can easily break.
You have replaced the bulbs and the brake switch still no bottom brake lights on a 95 Chevy lumina?
Check sockets and grounds
Why dont The brake lights on my 1966 Mustang not work and I have already replaced the switch?
Check the bulbs- they are double filamented with the smaller for brake lights Check the fuse Check the sockets for power and ground Check the sockets for corrosion
Why don't i have turn signals or flashers on the left side of my 1998 ford explorerAll bulbs and sockets are good?
One of the reasons why you may not have turn signals or flashers on the left side of your 1998 Ford Explorer if all the bulbs and sockets are good is you may have a blown fuse. Try replacing the light fuses or visiting an auto parts store to test the fuse to see if it is bad.
Why does the fuse for your tail keep blowing out after installing marker lights?
why does my turn signal light keep burning out and why is the sockets and plastic lens melted.
How is a calculator maintained?
Most calculators need very little maintenance. If keys are sticking, the keyboard can be disassembled and cleaned; batteries can be replaced and battery contacts cleaned; and charger sockets can be replaced or repaired. That is about it, though.
Why would the turn signals and flashers not work on a Mercury Grand Marquis after a jump start if the fuses and circuit breakers seem to be OK?
First check that ALL of your light bulbs are working for the signals. Some models will freeze operation of signals if a bulb is out to let the operator know that one needs to be replaced. Next check the flasher solenoid(s) near the steering column / brake pedal area. They are very cheap to replace. Also check that ALL of the signal sockets for the bulbs are in good shape. If they are burnt then it is the same as a bulb being out.
