0
What else can I help you with?
How do you remove the water pump pulley on a 1985 Oldsmobile cutlass ciera?
pulley puller
How to remove pulley from dodge water pump?
Best way is to purchase a water pump pulley remover, they are pressed on and have no way to grab with a conventional puller, the specialty puller is fantastic and not too expensive. Many are just bolted on so check that first.
How do you remove a pulley from a 1993 Chevy Caprice?
This depends on which pully you want to remove. The idler pulleys simply bolt on. The pulleys mounted on the water pump also bolt on. If you want to remove the harmonic balancer pulley, you'll need to remove the bolt in the center of the crankshaft, then use a puller. The pulley on the power steering must also be removed with a special tool. AutoZone(r), Advance Auto(r), and Murray's Auto have these pullers in stock and you may be able to rent one. You need a special puller sometimes rentable at the parts store.
How does water pump pulley come off a 89 celeberty 2.5?
A special puller is required to remove the water pump pulley from a 1989 Celebrity. The tool can be "borrowed" from Autozone on their "loner tool program". The same tool kit contains another tool to press the pulley back on. I did the job on my 1989 Celebrity with 2.5L, it was not difficult with the tool.
Where to find a puller to remove crank pulley in order to change water pump on a 1996 Dodge Intrepid?
Check with your local auto repair shot to see if they rent tools. If so, they likely carry a crankshaft pulley remover. I'm in the process of changing the water pump on my 2002 Intrepid and I rented the tool. Now I have to find the installer because the one they had didn't fit my pulley.
How do you get to the bolt located behind the power steering pulley to take out the water pump when there is no holes in the power steering pulley to remove the power steering pump?
Are you sure that bolt has to come out to change water pump? That bolt should be one of three that hold the p/s pump to the bracket. Those bolts are removed by removing the p/s pulley first. That requires a special puller to r & r the p/s pulley.
How do you take the water pump pulley off while it is still on the car without pulling the motor on the four cylinder engine?
It takes a special puller to take the water pump pulley off of the 4 cylinder engine. It is quite a tight fit but can be done with the engine in the car. Autozone has the special puller on their loaner tool program.
How do you take off power steering pulley on 1994 gmc?
To take the power steering pump pulley off of many later model GM products requires a special puller made for that purpose. It is available from Autozone on their loaner tool program. The same set includes another puller to put the pulley back on. Some water pumps also use the same style pulley.
How do I remove pulley that blocks water pump bolt?
The year, make, model and engine info would be helpful but, if that pulley is attached to the power steering pump, you may need to buy, rent or borrow a puller designed just for the job. Many auto parts stores wil rent you one.
Im changing out a water pump on a 97 dodge ram half ton with a 360 5.9 What is a three bolt puller?
its a three jaw puller for pressed on pulleys but you dont need it the crank pulley is bolted on
How do you change the water pump pulley on Cadillac eldorado?
after removing belt from tentioner and all surrounding items ,You Must Buy or Rent a STEERING PUMP PULLEY PULLER it looks like a small washer split in TWO with threaded rods to Pull off Pulley by the lip on it , a 2 or 3 fingered pulley puller WILL NOT WORK! Auto Zone or NAPA has these for about $30 it works easily .ask how to use it at the store.
How do you replace a pulley on a water pump on a 1989 Chevy Celebrity?
There should be a place for an Allen wrench to be inserted into the end of the water pump shaft, and a flat place for a spanner wrench on the pulley itself. An impact wrench may be required to break it loose, they can be very tight. Also, be aware of thread orientation. It also may be pressed on, if so you will need a puller to remove it.
