answersLogoWhite

0

To remove the electric back door panel on a 2005 Pontiac Montana Van, start by disconnecting the vehicle's battery to ensure safety. Use a flathead screwdriver to gently pry off any visible screw covers, then remove the screws securing the panel. Carefully pull the panel away from the door, starting at the edges, to release any clips holding it in place. Finally, disconnect any electrical connectors for the window or locks before fully removing the panel.

User Avatar

AnswerBot

2w ago

What else can I help you with?

Related Questions

How to remove the Pontiac Montana tailgate panel?

cant open tailgate


Where is the fuse panel in Pontiac Montana?

The fuse panel in a Pontiac Montana is located in the passenger door. It is located on the same level as the glove box.


How do you remove interior panel from lift gate on Montana?

To remove the interior panel from the liftgate of a Pontiac Montana, start by prying off any plastic covers or trim pieces that conceal screws. Use a screwdriver to remove the screws holding the panel in place. Carefully use a trim tool or flathead screwdriver to detach the panel from the clips around its edges. Once loose, gently pull the panel away to disconnect any electrical connectors and fully remove it.


How do you remove the center instrument panel containing the radioCD player on a 2002 Pontiac Montana?

take the the black thing around it and then take it out dont worry it wont brake


How do you remove the inner door panel on a Pontiac Montana?

remove screws. some may be hidden in the carpet and under tab covers.then the pannel will have one way or push ankers . just use a screwdrive to pry away.


How do you remove the door panel in a 2000 Pontiac grand prix gt?

just remove it


How do you replace door lock Pontiac Montana?

To replace the door lock on a Pontiac Montana, first, remove the door panel by unscrewing any visible screws and carefully prying it away from the door frame. Disconnect the wiring harness and any clips attached to the door lock mechanism. Remove the old lock by unscrewing it from the door and then install the new lock in the reverse order. Finally, reattach the door panel, ensuring everything is secured properly.


Why don't the dashboard lights work on the Pontiac Montana?

If all of the dashboard lights do not work at the same time on a Pontiac Montana, check the instrument panel relay. The relay is located on the firewall in the engine compartment.


Where is Fuse for sliding door on Pontiac Montana?

The power sliding door fuse is located in the passenger side fuse panel to the right of the glove box. You need to open the passenger door, remove the access panel on the side of the dash and consult the layout map on the panel as to which fuse is associated.


How do you remove the door panel on a 2001 Pontiac Grand Am?

Using a screwdriver, remove all the screws in the door panel and remove all the clips holding the panel to the frame. Gently pull the panel away from the frame, remove an wire connectors and pull the panel off the frame.


How do you lower the spare tire on a Pontiac Montana?

To lower the spare tire on a Pontiac Montana, first, locate the spare tire tool, which is usually found in the rear storage area. Remove the cover or access panel to expose the spare tire mechanism. Insert the tool into the access hole and turn it counterclockwise to lower the tire until it reaches the ground. Once lowered, you can remove the tire from the vehicle.


How do I remove the left side doorpanel on a 2000 Pontiac Montana?

To take off the interior door panel on Pontiac Montana,remove bolt under door pull (10mm).Remove plastic "scoop" behind handle and lock with flat screwdriver blade.There is another bolt under it. Remove it.Pry up plastic housing for lock and window controls with flat blade screw driver.Remove wiring ( 3 units - mirror, lock and window controls) from housingPry around entire panel with a large screwdiver or prybar,pulling outnylon screws from holes in sheet metal.Lift panel out over handle and lock module, feeding wiring from controls through hole so that panel comes free.Then remove clear plastic from inside of panel to access window mechanism.Now if I just knew how to test window controller or motor to see what's not working.