0
What else can I help you with?
How do you remove 94 Ford Ranger alternator pulley?
Use an impact wrench to remove center bolt and pulley should slide off
How do you remove the alternator on a 1995 Chrysler cirrus?
remove core support and cooling fans. this will allow you room to operate. remove top mounting bolt. slide belt off idler pulley. remove mounting bracket located to the right of the alternator. put a wrench on the nut on the backside of the alternator and a ratchet and 3" extension on the front side. remove the bolt. alternator should be ready to disconnect. to replace reverse the process.
How do you replace alternator cummins?
Disconnect the battery, remove all wires from the alternator, slacken the belt tensioner, slip the belt off of the alternator pulley, unbolt the alternator, and remove the alternator. Installation is the opposite of removal.
How do you change the belt on 1974 Air Cooled Super Beetle?
take the pulley nut off the alternator....the pulley is split.....shims between the two pulley halves adjust the belt tension
Install 84 t bird alternator?
Loosen the tensioner pulley. The alternator belt will become loose. Take off the belt. Remove the wiring harness from the alternator. Remove the retaining bolts from the alternator. Remove the alternator. Reverse the process to install the new alternator.
How do you replace the transmission drive belt on a 13AM675G062 MTD lawn tractor?
Remove battery, take out battery tray then remove nut on top of pulley take pulley off slide the new belt on then replace the nut
How do you replace the alternator on a 1996 Saturn SC?
Loosen up the lugnuts on the passenger side front wheel. Jack up the passenger side front of the vehicle. Take off the wheel. Remove the splash shields that cover the inside of the wheel well. If you look from the passenger side top of the engine, you will see the belt connected to up to 7 pulleys. No matter how many pulleys you see (it will depend on if your car has AC, etc..) the alternator is connected to the bottom left pulley. You can distinguish the alternator because right behind the pulley is a small fan, connected to the alternator itself. Directly to the right of the alternator is your tensioner pulley, held on by a nut. Get a wrench that will fit that nut, and turn it clockwise. This will loosen the tension on the belt, but hold it in that position with one hand because the pulley is springloaded, and will spring back into place as soon as you let off tension. Take the belt off of the alternator pulley. If your belt is getting old, mine as well replace it now because you'll kick yourself later on when you could have just spent the $20 and had it over with. Now, just loosen the bolts from the alternator and disconnect the wiring. If your new alternator came with a pulley already, you are ready for install. If not, you will have to get a pulley puller and remove the pulley from the old alternator and press it onto the new one. (TIP: most chain auto parts stores will do this for you!) Connect the wiring to the new one, and bolt it in place. Turn the tensioner pulley nut clockwise again, and put the belt around the alternator pulley, making sure that the belt did not slip off of any other components. Put the wheel well back together and put the wheel back on. Congratulations, your done.
How do you change an alternator on range rover vogue v8?
Loosen the tensioner pulley to remove the belt. Remove the wiring harness. Remove the retaining bolts. The alternator will come off and can be replaced with a new one.
How do you take off alternator tension on a 99 Mazda 626 v6 car?
To release the alternator tension on a 1999 Mazda 626 V6, first, locate the tensioner pulley, which is typically near the alternator. Use a wrench or ratchet to rotate the tensioner pulley counterclockwise, which will loosen the serpentine belt. Once the tension is released, you can slide the belt off the alternator's pulley. Afterward, you can remove the alternator if needed.
How do you install alternator on 2004 impala?
First you will need to remove the coolant tank, then take the serpentine belt off of the alternator pulley. Next unplug the factory wire harness from the alternator and remove the bolts that hold it in place.
Do you have to remove the mounting bracket when replacing the alternator in a 1999 Chevrolet Tahoe?
No, you do not have to remove the bracket to remove and replace the alternator. There are the two main bolts under the alternator which thread into the bracket on the back side that hold the alternator in place. After that, only a 13mm nut securing a wire (back side) and a plug (bottom, back side) which has 4-6 wires. To loosen the alternator belt (which may be confusing you) you must put a wrench or socket on the tensioner pulley and pry counter clock-wise. This will allow you to slip the belt off of the alternator pulley (should be done first during removal, last during replacement)
How do you remove the alternator on a citroen xsara?
To remove the alternator from a Citroën Xsara, first disconnect the battery to ensure safety. Then, remove the drive belt by loosening the tensioner and sliding it off the alternator pulley. Next, disconnect the electrical connections from the alternator, followed by unbolting the alternator from its mounting bracket. Finally, carefully lift the alternator out of the engine bay.
