0
To remove The speakers you need a very simple Philips head screwdriver, that's it.
First, put the convertible top about halfway down, because this allows easy access to the speaker assembly.
Once the top is halfway down, look near the 1/4 windows towards the back of the car, their will be a vinyl covering that covers the speakers, this snaps off easily.
Now, the speaker assembly should be revealed. carefully unscrew the speakers from the panel, or for a custom installation, unscrew the 4 or 5 screws located around the speakers central point that are in various locations, once this is done, disconnect the speaker's wire harness, the harness is located under the panel that supports connection for you tonnue cover (also know as the convertible boot or "top cover").
You can now pull the speaker out. If you have decided to remove the panel, as i have done, this is how to remove it properly.
The panel should be pulled from the back, and then up, because the speaker panek built to "lock" into the fake leather (vinyl) panel located above the small armrest for backseat passengers.
You can either attach the the factory wire harness to the speaker wires by soldering the positive and negative wires, or use clips to connect them, I found it was easier to use the factory harness.
Now, fabricate the speakers to you liking. If you want them to be hidden, munt the speakers using factory holes, and then connect the wire harness. You now have sound.
*** for custom rear fabrication of the speakers, you can remove the cloth material, and cut the perferated speaker holes out, then sand and paint the panel. this requires time and a dremel, but it really adds a custom look to your beloved little convertible.
In summation, this will add a touch of customization to your car. I fabricated the speakers so they are scene and it really added a lot to my interior. I love my Chrysler LeBaron Convertible, and I hope you do to.
What else can I help you with?
How do you replace the back speakers in a 1991 Chrysler LeBaron?
is it a convertible? if so the onlt thing that you do is lift the flap in the corners ( with the top up of course) and there you will find the speakers. Simply undo the screws and unhook the connection. Then you put the new speakers back in the holes, attach the wires and put the screws back in.
Where is fuel pump located on Chrysler lebaron convertible?
It is located in the Fuel Tank which means the Tank will need to be dropped in order to replace the Pump.
How do you replace a convertible top on a 1993 LeBaron?
Take it to a professional. This is not a DIY job.
How do you change the transmission filter on a 1995 Chrysler LeBaron convertible?
To change the transmission filter on a 1995 Chrysler LeBaron convertible, start by draining the transmission fluid by removing the transmission pan. Once the pan is off, you'll see the filter; unbolt and remove it. Replace it with a new filter, ensuring any gaskets or seals are properly positioned. Reattach the pan, refill the transmission with fluid, and check for leaks.
Where is the thermostat for a 94 Chrysler Lebaron convertible located?
Follow the hose from the top of the radiator back towards the engine, where it connects is the thermostat housing, this can be removed by taking out the 2 bolts. - remember to replace the gasket!
What size are the speakers in a 92 Chrysler lebaron?
For the 1992 Lebaron Convertable: In-dash speakers are 3 1/2 inches, door speakers are 5 1/4 inches, and the rear seat side panel speakers are 5 1/4 inches. [I found this information on the Crutchfield web site when I was preparing to replace the speakers in my Lebaron. Worth noting, the site also provides a list of car audio components that fit based on your make, model, year and (where appropriate) car type.]
How do you replace Chrysler lebaron dash speakers?
remove the grills connect two 3 1/2's (the left will fit VERY TIGHT) but it replaced cardboard and wired into pre made slots for the speakers very easy in the end.
How long would it take approximately to replace the timing chain on a 1997 Chrysler lebaron?
The last Chrysler LeBaron was in 1995. Both engines available that year had timing belts.The last Chrysler LeBaron was in 1995. Both engines available that year had timing belts.
How to replace a Chrysler lebaron convertible body control module?
To replace the body control module (BCM) in a Chrysler LeBaron convertible, first disconnect the negative battery terminal to ensure safety. Locate the BCM, typically found under the dashboard or near the steering column. Remove any covering panels, disconnect the wiring harnesses, and unbolt the module from its mounting bracket. Install the new BCM by reversing the removal steps, reconnect the wiring, and reattach any panels before reconnecting the battery.
How do you change rear brakes on 1992 Chrysler lebaron convertible?
To change the rear brakes on a 1992 Chrysler LeBaron convertible, first, lift the rear of the vehicle and secure it on jack stands. Remove the wheel and then the brake caliper by unbolting it, allowing it to hang (do not disconnect the brake line). Replace the brake pads and, if necessary, the rotors, then reassemble by reversing the disassembly steps. Finally, pump the brake pedal to ensure proper brake function before lowering the vehicle.
How do you replace 1988 Chrysler LeBaron brakes?
Front or rear.. disc or drum type..??????????
How do you repair the brakes on a 1992 Chrysler lebaron?
be more specific.. replace pads..?? replace hose..?? repair master cylinder..??
