0
I'm assuming the answer to this question will be the same answer to the "How do you replace a rear brake light bulb on a 2001 Jeep Grand Cherokee Limited Edition?" question. The following is what was posted:
Rear: Brake, Back-up, Tail, Turn signal (3 bulbs, all # 3157)
To access the rear bulbs, open the liftgate and remove the two Phillips head screws from the side of the housing as shown in the center photo above. Slowly and firmly rotate the assembly away from the vehicle until it disengages from the ball pin socket that secures it in back.
Each of the three light sockets, all containing the same exact bulb type, can be removed by turning them counter-clockwise 1/4 turn.
Taillight harness connector
To remove the taillight harness, slide the red lock tab up and pull connector off.Well, I guess people should not make those sort of assumptions - the 1994 Jeep Cherokee was still one of the old-style box shaped Cherokees, nothing like a 2001 model at all, and it has much more old-fashioned lights.Actually, changing the tail lamps is a real pain. I know, I spent about 2 hours this morning replacing a broken driver's side fitting on my 1993 Cherokee. Open the trunk. The light fitting is held on by 3 obvious bolts. You'll need a socket set to shift them (I think I used a 3/32" bit). The fun begins because there is also a 4th bolt, hidden behind the lower bumper. You have to disassemble the end of the bumper to get at this (take off the plastic end cover that is attached to the metal bumper bar.) This itself is held on by 3 bolts. Hmm... undoing metal bolts that had been in place since 1993 (most likely), exposed to all weathers. That was fun (not). My hands are sore.Once you have taken out the four bolts that hold the big boxy plastic light fitting in place, it should fall forward from the car easily. To replace the bulbs, gently turn the metal holders 1/3 of a turn clockwise. They should retract back through the plastic fitting, allowing you to unnscrew the old bulb, and replace it.Good luck!
What else can I help you with?
Rear light failure on 1994 Jeep Grand Cherokee?
Replace the bulbs
Where do you find the brake light fuse in a 1994 Jeep Grand Cherokee?
passenger side fuse panel....#2
How do you replace 1994 Lexus es300 brake light bulb?
you dont you get a new car
If the dashboard brake light is on in a 1994 Cherokee does that mean you need new brakes?
Try checking Brake fluid level if ok then cxheck pad wear.
How do you replace the center brake light in a 1994 Honda Accord?
Look inside the trunk under the light for bolts to remove the light.
1994 Chevrolet Cavalier Z24 brake light and abs light on?
brake and abs light on , on 1994 Chevy Cavalier Z24
How do you replace brake light switch on a 1994 Mercedes C280?
To replace the brake light switch on a 1994 Mercedes C280, first disconnect the negative battery terminal to ensure safety. Locate the brake light switch, which is typically mounted on the brake pedal assembly. Remove the electrical connector and the switch by unscrewing it or releasing any clips holding it in place. Install the new switch, reconnect the electrical connector, and reattach the battery terminal before testing the brake lights.
How do you replace a flexplate on a 1994 Jeep Cherokee?
The transmission will have to be removed.
How do you replace the Brake Light Sensor on a 1994 Chevy Truck?
It's just above the brake pedal, connected to the brake pedal arm. The switch comes out with two screws and the new one plugs in. But before you replace the switch, check the adjustment.
How do You change a brake light on a 1994 Chevy van?
special bit for light lens cover, t 10 or t 20 bit light bulb unscrew from socket replace observe ligh light place foot on brake , re screw use brick on brake pedel
How do you replace brake light bulb in a 1994 Volvo 940?
Take the cover off in the trunk and turn the bulb socket to the left.
1994 Dodge Dakota the headlights tail lightsdashboard panel lights and brake light will not turn on?
replace the headlight switch its wore out replace the headlight switch its wore out
