answersLogoWhite

0

Depending on the year, this should be covered by warranty, as there was a recall for these parts on some years. Check with a dealer to see if this applies.

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

How do you install Stabilizer links on a 2000 ford explorer 4x4?

If its the front link 3 piece desing, just pry up on the swaybar, insert the center section and run the long bolt through it.


How to replace front brake rotors on a 2000 ford explorer sport 4x4?

How to Install Front Brake Pads Check Related links below.


How do you remove door panel 2010 ford explorer?

How do I install passenger side mirror 2010 Ford Explorer


On the front end of a 1998 Ford Explorer what does the bar attached to the frame with a small rod at each end do What are the two small end rods going up and down called?

The bar is called the stabilizer bar and the small rod at each end are called stabilizer bar links. The stabilizer bar links attached the stabilizer bar to the lower control arms. This assembly reduces vehicle roll during cornering. This is good information for you, call Strutmasters they can help you with any of your suspension needs on this vehicle.


How do you remove the dash board to install a CD player in a 2002 Ford Explorer?

I need an answer to my question. how do you remove the dashboard to install CD player in a 2002 ford explorer. thank you.


How do i install motor mount on a 1998 ford explorer 4.0?

explorer engine mounts removal


What is the earliest ford explorer you can install a third seat?

The first model year that a Ford Explorer was available with a third row seat was ( 2002 )


How do you install a Ford CDradio into a 1994 Ford Explorer?

Here's a good link: http://www.installdr.com/


How do you Remove door panel 2010 Explorer?

How do I install passenger side mirror 2010 Ford Explorer


How do you replace the stabilizing links on the front sway bar of a 2000 ford explorer?

I believe it is a 15mm nut and bolt. You need to undo both stabilizer links and pull the bolt out of the stabilizer link shaft. Sometimes these parts will rust together or corrode and can be tough to pull apart but they will come apart. Then you just replace the old with the new. total job time for both sides... 20 - 40 mins. hope this helps.


How many times do you turn a torque converter 94 ford explorer?

how install torque converter 94 explorer


Can you install 265 70 R16 tires on 02 ford explorer?

Yes

Trending Questions
Where is the engine control module - ECM - on a Ford Freestar or Mercury Monterey? What was the purpose of vat? What is the answer to this question American car makers produce 5650000 cars each year's. In a report ben wrote that Americans made 6550000 car's. What mistake did ben make How can he fix it? Where is the thermostat located on the 2001 Chrysler Concorde? How do you reach a clogged air conditioning drain line in order to clear it on a 1998 Mercury Tracer LS that is leaking water onto the passenger side floor? Where is a Saturn sl1 spare tire? What could cause low oil pressure in a Z24 Cavalier? What is the problem if the front AC works great but the rear AC blows hot air on a 2002 Tahoe? Would a Chevy 350 heads fit on a 400 engine? 1984 F150 XLT what engine is in this truck? Where is the block heater cord on a 2003 Chevy Cavalier? Is the Saturn Ion front wheel drive? Where can you find a fuse box diagram for a 91 Tempo when we have no cover? What is the Firing order of 1984-86 ford f250? Does AC blow hot air from bottom to top or cool air from topto bottom in a room? What could be the problem When the turn signals won't work and the car wont start but sometime they work and the car then starts? Is it normal for a 2000 Chevy Blazer temp gauge to go to three quarters when driving in traffic even after the thermostat was replaced? How does one know gm tbi fuel injectors are bad? Waste oil produced a year in US? How do you change timing belt 2001 Chrysler Concorde lxi 3.2L?