0

Subjects>Auto>American Cars

What is the torque spec for the water pump mounting bolts on a 2000 subaru legacy?

Anonymous

∙ 15y ago

Updated: 10/27/2022

The torque should be around 11 ft-pounds

Wiki User

∙ 15y ago

What else can I help you with?

Related Questions

What is the torque specs for the brake caliper mounting bolts on a 1999 subaru legacy?

Front caliper mounting bracket bolts torque to 57ft-lbs Front caliper pin bolts torque to 27ft.lbs Rear Caliper mounting bracket bolts torque to 38ft-lbs Rear caliper pins torque to 15ft-lbs

What is the torque specs for the brake caliper mounting bolts on a 2002 Subaru Outback LL Bean H-6?

The caliper mounting bolts, both in the front and in the rear, require 39N-m, or 28.9 ft-lbs of torque.

Torque specs for a 1995 Subaru impreza 2.2 head bolts?

Torque specs for a 1995 subaru impreza 2.2 head bolts?

What is the torque specs for the brake caliper mounting bolts on a 2005 Nissan Frontier?

32ftlbs for the pin bolts

What is the torque specs for the brake caliper mounting bolts on a 2005 Mazda 6?

Torque specs for brake caliper bolts 2005 mazda 6

Can someone tell you what the torque settings are for a 2006 Honda CRV front brake caliper mounting bolts and also the caliper bracket bolts?

Front caliper bolts 25 ft/lb Mounting bracket bolts 80ft/lb

What is the torque pounds when installing anew water pump and pulley on a 1986 lesabre?

Long mounting bolts 22-29 ft lbsShort mounting bolts 96 - 132 in lbsPulley bolts 108 - 132 in lbs

2002 Buick Century front hub torque for mounting bolts and axle nut?

34mm

How many bell housing bolts on a Subaru legacy?

Subaru 2000 Outback: Tranny side - 10 bolts, Engine side - 8 (including starter bolts). Tranny M/N TZ1A4ZCABA-WL. You're welcome!

What is the torque specs for 07 wrx brake caliper?

The torque specifications for the brake caliper bolts on a 2007 Subaru WRX are typically around 79 ft-lbs (107 Nm) for the caliper mounting bolts. It's important to ensure that the caliper bolts are properly torqued to avoid any issues with braking performance. Always refer to the vehicle's service manual for the most accurate and specific information.

Torque specs on alluminum p51 intake mounting bolts?

Fox Lake Racing P-51 Intake Manifold mounting bolt torque spec. is ( 18 lb-ft ) 25 Nm

What is the torque specs for the brake caliper mounting bolts on a 2000 buick lesabre?

75 ft lbs

Trending Questions

Where is the intake manifold runner on a 2003hold maita? Where is the power steering motor in a Saturn Ion 2? Where is the antenna on 1998 mercury grand marquis? Where is the PCV valve located on a olds 96 achieva 2.4? How do you replace a licence plate bulb on a 1995 Buick Lesabre? What size speaker are in a 1996 sonoma? What side of the exhaust is the oil drain plug on a buell blast? Is the 2009 Cadillac CTS front wheel drive? Whats wrong with your car if the cooling fan does not turn on when you turn the car on you tryed a new fan and the new on dosent turn on either what would be the problem? Is the 2010 camaro rwd or fwd? What year do vehicles become tax exempt? Will 15 inch wheels clear the brakes on a 07 jeep wrangler? How much should it cost to replace the computer on a 99 Plymouth Voyager? What is the weight of the 1985 El Camino? What type of refrigerant oil should you use for a 2004 buick lesabre and what viscosity? Your 1985 Nissan 300zx turns over but wont start? How often do you change Differential fluid for 2004 Jeep Liberty? What would cause a smell from the heater of a 99 Ford Taurus wagon that at first smells like a farm then turns to a maple-syrup smell when warmed up? Where is the jack located on a dodge stratus? Is there a different abbreviation for cellular in America?

Resources

Top Categories

Product

Company

Copyright ©2025 Answers.com. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Answers.