0
What else can I help you with?
How do you pull out a torque converter in a 2002 volkswagen beetle?
To remove the torque converter from a 2002 Volkswagen Beetle, first, disconnect the battery and drain the transmission fluid. Next, remove the transmission pan and the transmission mount to access the torque converter. Unbolt the torque converter from the flex plate while rotating the engine to access all the bolts. Finally, carefully pull the torque converter out of the transmission once it is unbolted.
How do you take torque converter off of engine so you can mount the motor on a stand?
The Torque Converter is part of the transmission, not part of the engine. The torque converter needs to come off with the transmission. You need to remove the starter to access the torque converter bolts/nuts and separate it from the flex plate. Besides loosing all of the fluid in the torque converter, you stand to damage converter seals and/or the pump if the converter isn't properly installed in the transmission.
Will my torque converter flex plate spacer plate and starter from my c4 fit an aod transmission?
your spacer plate and starter should be the same the flex plate and converter will need to be replaced
How do you change Torque converter?
major job for the inexperienced you must first remove the transmission then you remove torque converter from flex plate. flex plate is equivalent to a fly wheel in a standard gear box to replace torque converter, is another job in itself as it must be installed loosely until transmission is installed , then properly filled with transmission fluid then tightened properly if not sure about all this, it is likely to not work or fail going down the road WAIT!, ..unbolt the torque converter from the flex plate and remove with the transmission! If you pull the transmission separately, you risk damaging the pump in the transmission! Same applies going back in, the torque converter needs to be meshed into the front pump of the transmission before putting into the car. Then once the transmission is bolted to the engine, THEN you bolt the torque converter to the flex plate. If you do as described in the first answer, you will very likely end up replacing the entire transmission! This job requires experience and special tools, not for the beginner.
What is the flex plate on your 1997 Plymouth Breeze?
It is the ring gear and plate that conects your engine and automatic transmission's torque converter.
How do you remove a Chevy 350 Transmission?
Remove the driveshaft from the back of your Chevy transmission. Remove the transmission mount retaining bolts. Remove the retaining bolts from the Bell housing. The transmission can then slide backwards. Don't forget to unbolt the torque converter from the flex-plate and remove the torque converter with the transmission.
What is causing rattling noise inside automatic transmission?
Loose timing chain? Loose heat shield on catalytic converter?
How do you replace a flex plate in a 2002 Pontiac grand prix?
The flex plate is bolted to the back of the crankshaft. It connects the motor to the torque converter in the transmission. To replace you remove the transmission and replace it.
Does the torque converter have to be removed to change out a transmissions on 2001 Chevy X Z?
It must be unbolted from the engine flex-plate (flywheel) then correctly installed into the replacement transmission. Failure to install the torque converter correctly will result in expensive damage to the transmission.
What is the bell housing?
It is located between the back of the engine and the transmission. It houses the flywheel and clutch if it is a standard or the flex plate and the torque converter if it is an automatic transmission.
How do you replace torque converter on 1995 GMC Sonoma 700R4 transmission?
pull engine, unbolt torque converter from flex plate (3 bolts), fill new torque converter with ATF fluid(so it dont start up dry), place new torque converter on to the transmission input shaft, reinstall engine, from underneath now u can spin the engine over by hand to line up the bolt holes and tighten the torque converter to the flexplate.
How can you remove a torque converter from a flex plate 2000 GMC sierra 1500?
To remove the torque converter from the flex plate on a 2000 GMC Sierra 1500, first ensure the vehicle is securely raised and supported. Remove the transmission oil pan and drain the fluid. Then, unbolt the torque converter from the flex plate using the appropriate socket, usually accessible through the inspection cover or by rotating the engine to reach all bolts. Once unbolted, you can carefully pull the torque converter away from the flex plate.
