0
Where is the ABS Computer on a 1991 Caprice and how can you disconnect it so it can release pressure on a caliper?
that's not how you relese pressure on the caliper. you disconnect the brake fluid hose from the caliper and that will relese the pressure. if the caliper still won't move then you need to take the caliper apart and clean it good because the piston is most likely getting stuck.
What else can I help you with?
How do you disconnect a 1996 Ford Escort left front brake caliper?
Remove wheel Re-install 2 lug nuts to hold rotor in place Disconnect flexible brake line Remove caliper mounting bolts Slide caliper off rotor
How do you replace front caliper and pads to 2002 Kia Optima?
Jack up the 2002 Optima and remove the wheel. disconnect the caliper brake line and drain into a bucket. Unbolt the caliper, and remove it with the pads. Bolt the new caliper on and replace the pads. The brakes may be spongy and the new caliper will require bleeding.
How do you compress caliper piston?
To compress a caliper piston, you can use a brake caliper tool or a C-clamp. First, ensure the brake fluid reservoir cap is loosened to avoid pressure buildup. Then, position the tool or clamp against the piston and the back of the caliper, and slowly apply pressure until the piston is fully retracted. Be cautious not to damage the piston or the caliper during the process.
How do you remove the rear caliber in 1997 Oldsmobile Aurora when the rear brake is locked up?
removing caliper 1996 olds aurora lockedNote that many times the "locking" can be caused by a sticking e-brake cable rather than a locked caliper. Check to verify that there is some slack in the cable at the caliper when the parking brake is released. If not, the cable may be seized in its jacket somewhere, and will have to be freed or replaced. If the caliper is locked, you will need to disconnect the brake line to remove the line pressure. Then disconnect the e-brake cable, then the caliper. If it is still stuck, you will need to retract the piston inside the caliper - sometimes they stick and you have to lube the caliper and hit the caliper with a hammer lightly or it can crack. Another way is to CAREFULLY heat the caliper with a torch until the caliper expands and releases. If any question please e-mail me Ben. thejamesclan5@msn.com good luck!Don't try to re-use a caliper that has locked. While you may be able to free it temporarily, they almost always end up sticking again. The cost of a loaded new or remanufactured caliper assembly is cheap insurance against it sticking any time in the near future.
What is the torque specs for the brake caliper mounting bolts on a Chevrolet caprice 1996?
The torque specification for the brake caliper mounting bolts on a 1996 Chevrolet Caprice is typically around 25-30 ft-lbs. It's important to ensure that the bolts are tightened to the manufacturer's specifications for optimal performance and safety. Always consult the vehicle's service manual for the most accurate and specific information.
How do you replace rotors on a 1990 camaro?
remove tire. remove caliper assembly, it is not necessary to disconnect brake hosses, and hang caliper out of the way. simply pull off old rotor and swap with new one. replace caliper assembly and tire.
How do you replace caliper on a 1990 Dodge Caravan?
Remove wheels Re-install 2 lug nuts to hold rotor in place' Disconnect flexible brake line Remove 2 caliper mounting bolts Slide caliper off rotor
How do you replace rear wheel bearing hub assembly in a 2001 Saturn?
Remove Wheel Remove 2 caliper mounting bolts Slide caliper off rotor Remove rotor Disconnect Brake line Remove 4 mounting bolts Disconnect ABS sensor if any
What size wrench is needed to remove the caliper mounting bolts on 1991 caprice?
Most likely a 3/8 Allen, but 15 mm wrench is possible.
How do you change the rear brakes for a 92 caprice classic?
You will need to remove the tire and wheel from your 1992 Chevrolet Caprice Classic. Remove the brake shoe spring and caliper. The brake shoes will come off. Reverse the process to install the new brake shoes.
How do you get the caliper piston to go back in on a 1984 Chevy caprice classic I took the cap off the master cylinder and I tried to push it back in with a very big C clamp but it won't budge?
Sounds like the caliper is frozen. Probably needs to be rebuilt or replaced. If you decide to rebuild the caliper yourself make sure the bleeder screw comes loose without breaking off before rebuilding it, otherwise you can't bleed the air out of it when you're done. A rebuilt caliper from a parts store for an '84 caprice is real cheap anyway and it's easier and faster to just replace it.
HoW to remove rear caliper on 1995 Buick Riviera?
To remove the rear caliper on a 1995 Buick Riviera, start by safely lifting the vehicle and supporting it with jack stands. Remove the wheel to access the caliper, then detach the caliper by unbolting the caliper mounting bolts. After removing the bolts, slide the caliper off the brake rotor, and disconnect the brake line if necessary. Finally, support the caliper with a bungee cord or similar tool to avoid straining the brake line.
