0
On a 1988 Ford F-150, the wiper motor control module is typically located under the dashboard on the driver's side. It can often be found near the steering column or mounted to the firewall. Accessing it may require removing some panels or components for better visibility and reach. Always refer to a service manual for specific details related to your vehicle's configuration.
What else can I help you with?
Where is the wiper motor on a 1988 jeep wrangler located?
The 1988 Jeep windshield wiper motor is located on the firewall in the engine compartment. The wiper motor will be in the center of the firewall.
1988 Pontiac Trans Am GTA Headlights Relay Location?
If you are standing at the front of the car, the module is located on the right side of the firewall by the windshield wiper motor....
Where is 1988 bronco --4x4 solenoid control module located?
It is located on the transfer case this is the motor that shifts your four wheel drive
1988 cadilliac brougham where is the wiper timer located thanks be?
Its mounted on the washer pump/wiper motor.
How do you change the ignition control module in a 1988 Chevy Silverado 5.7 L?
How do you change the ignition control module in a 1988 Chevy Silverado 5.7L
Where is the wiper pulse board location on a 1988 gmc 1500?
it on the top left side of the wiper motor where the plug goes in
How do you fix windshield wiper motor on a 1988 crx Honda?
To fix the windshield wiper motor on a 1988 Honda CRX, first ensure the problem is indeed the motor by checking the fuse and wiper switch. If those are functional, remove the wiper arms and the cowl panel to access the motor. Disconnect the wiring harness and remove the mounting bolts to take out the faulty motor. Replace it with a new or refurbished motor, reassemble the components, and test the wipers to ensure proper operation.
How do you change wiper motor it Isuzu npr 1988 truck?
To change the wiper motor on a 1988 Isuzu NPR truck, first disconnect the battery to ensure safety. Remove the wiper arms by loosening the nuts at their bases, then take off the plastic cover to access the motor. Disconnect the wiring harness and unbolt the wiper motor from its mount, then replace it with the new motor and reverse the steps to reassemble everything. Finally, reconnect the battery and test the wipers for proper operation.
How do you remove the windshield wiper motor on a 1988 Pontiac Firebird?
To remove the windshield wiper motor from a 1988 Pontiac Firebird, first disconnect the negative battery cable to ensure safety. Then, remove the wiper arms by taking off the nuts securing them and carefully prying them off the motor spline. Next, access the motor by removing the interior panel under the windshield, and disconnect the electrical connector. Finally, unbolt the wiper motor from its mounting bracket and carefully pull it out.
Where is the control module in an 1988 fifth ave?
Taking a guess, Your 1988 5th Ave has a 318ci motor with Lean-Burn Engine control. Chrysler put the control module in the rectangle box attached to the side of the air cleaner. All of the engine control module is inside that box to include the transistorized ignition system. Your distributor will have two pickup coils in it and not have a vacumn advance located on the side of it which will be another way of telling if you have the Lean-Burn system.
How do you remove the ignition module on a 1988 ford f-250?
how do you remove the ignition control module on a 1988 ford f-250 pickup?
How do you remove the windshield wiper motor on a 1988 Firebird?
To remove the windshield wiper motor on a 1988 Firebird, start by disconnecting the negative battery cable to ensure safety. Next, remove the wiper arms by unscrewing the retaining nuts and pulling them off the splines. Then, access the motor by removing the interior panel or cowl cover, followed by disconnecting the electrical connector and unscrewing the motor from its mounting bracket. Finally, carefully pull the motor out of its housing.
