0
How do you repair the automatic trunk closing system on a 1987 Cadillac Brougham Or is it just easier to install a manual type?
YOU HAVE TO EXPLAIN IF ITS THE RELEASE OR PULL DOWN THATS NOT WORKING.
I'LL GUESS THAT IT'S THE PULL DOWN. IF THATS THE CASE AND THE MOTOR IS
GOOD,(RUNS IN BOTH DIRECTIONS WHEN 12VOLTS IS APPLIED) IT'S MORE THAN LIKLY
THE LOWER SWITCH THATS MOUNTED ON THE MOTOR. I WOULD RATHER KEEP THE
ORIGINAL THAN GO TO MANUAL,IT'S NOT A BIG JOB.
GOOD LUCK
PAUL G
I have the same prob, changed the motor and no go. where can I get the wiring diagram for this closing motor
The wiring diagrams for these electronic details aren't included in the Haynes or Chilton manuals, but there are good diagrams and fault search test procedures for nearly all electric accessories of the Cad in Cadillac's own workshop manual. It is a thick book but very very good, and can still be found at eBay.
What else can I help you with?
How do you replace an alternator in an 1987 Cadillac brougham?
Begin by removing the alternator belt. Remove the wiring harness from the back of your alternator. Remove the alternator retaining bolts. Reverse the process to install your new Cadillac alternator.
How do you install an 89 Cadillac Brougham power steering belt?
Well, isn't that a happy little question! To install the power steering belt on your 89 Cadillac Brougham, start by locating the belt tensioner pulley. Use a wrench to rotate the tensioner, allowing you to slip the belt over the pulleys. Make sure the belt is sitting properly in all the grooves before starting your engine and enjoying a smooth ride down the creativity highway.
How do you replace heater core in 91 Cadillac brougham?
To replace the heater core in a 1991 Cadillac Brougham, start by disconnecting the battery and draining the coolant. Remove the dashboard and the center console to access the heater core's housing. Disconnect the hoses from the heater core and unbolt it from the housing. Install the new heater core, reassemble the dashboard, reconnect the hoses, and refill the coolant before starting the vehicle.
How do you repair or replace the power antenna on a 1991 Cadillac Brougham?
To repair or replace the power antenna on a 1991 Cadillac Brougham, first, remove the interior panel near the antenna to access the mounting screws. Disconnect the antenna wiring and unscrew the old antenna from its base. If replacing, install the new antenna by securing it in place, reconnecting the wiring, and reattaching the interior panel. Test the antenna to ensure it extends and retracts properly.
How do you install air compressor belt on a 1988 Cadillac Brougham?
To install the air compressor belt on a 1988 Cadillac Brougham, first ensure the engine is off and cool. Loosen the tensioner pulley by turning the adjusting bolt, which will allow you to remove the old belt. Route the new belt around the air compressor pulley and any other pulleys according to the belt routing diagram, then tighten the tensioner back to maintain proper tension on the belt. Finally, double-check the alignment and tension before starting the engine.
How do you install a maf sensor on a Cadillac deville concours?
how to install a maf sensor on a cadillac deville concours?
How do you replace an alternator on a 91 Cadillac Brougham?
To replace the alternator on a 1991 Cadillac Brougham, first disconnect the negative battery terminal to ensure safety. Remove the serpentine belt by loosening the tensioner, then disconnect the electrical connections from the alternator. Unbolt the alternator from its mounting bracket, install the new alternator in reverse order, reconnect the electrical connections, and reattach the serpentine belt. Finally, reconnect the battery terminal and start the engine to test the new alternator.
How do you replace an alternator belt on a 1987 Cadillac Brougham?
To replace the alternator belt on a 1987 Cadillac Brougham, start by disconnecting the negative battery terminal for safety. Then, locate the alternator and loosen the adjustment bolt and the pivot bolt to relieve tension on the old belt. Remove the old belt and install the new one, ensuring it is properly seated on the pulleys. Finally, adjust the alternator to create adequate tension on the new belt, tighten the bolts, and reconnect the battery terminal.
How do you replace a water pump on a 96 Cadillac Fleetwod brougham?
To replace the water pump on a 1996 Cadillac Fleetwood Brougham, first disconnect the battery and drain the cooling system. Remove the serpentine belt, and then take off any components obstructing access to the water pump, such as the fan and shroud. Unbolt the old water pump, clean the mounting surface, and install the new pump with a new gasket. Finally, reassemble everything, refill the cooling system, and check for leaks.
How do you replace a power steering pump on a 89 Cadillac brougham?
To replace the power steering pump on a 1989 Cadillac Brougham, first, disconnect the negative battery cable and drain the power steering fluid. Remove the drive belt and the mounting bolts of the old pump, then carefully detach the pump from the steering gear. Install the new pump by reversing the removal process, ensuring all connections are secure. Finally, refill the power steering fluid and check for leaks before reconnecting the battery.
How do you replace the heater core on a 1990 Cadillac brougham?
To replace the heater core on a 1990 Cadillac Brougham, start by disconnecting the battery and draining the coolant. Remove the dashboard and the center console to access the heater core, which is typically located behind the firewall. Disconnect the hoses and any electrical connections, then unbolt and remove the old heater core. Install the new heater core by reversing the disassembly steps, ensuring all connections are secure before refilling the coolant and reconnecting the battery.
How do you replace a carburetor for a 1987 Cadillac Brougham?
To replace the carburetor on a 1987 Cadillac Brougham, first disconnect the negative battery cable and remove any air cleaner components for access. Carefully detach the fuel lines and linkage from the old carburetor, noting their positions for reassembly. Remove the mounting bolts securing the carburetor to the intake manifold and lift it off. Install the new carburetor by reversing the removal process, ensuring all connections are secure and then reattach the air cleaner before reconnecting the battery.
