0
Do you have to power down the system before connecting a usb camera why or why not?
Wiki User
∙ 14y ago
No. When you disconnect a device or peripheral from a PS/2 port and the computer it's on that can cause a spike and a short circuit damaging your computer. So, it's more dangerous if it is connected to a PS/2 port than in a USB port. E.g. It's like connecting a USB Flash drive.
Wiki User
∙ 14y ago
Wiki User
∙ 15y agoNo
Add your answer:
Earn +20 pts
Can one use a three wire cable or the same ground wire when sending power to a video camera and receiving a signal from that camera?
It's possible, but it depends a lot on the electronics of the camera and whether or not it's being operated by an AC or DC power source. In fact, it's even possible to send the video over a two wire system, such as the power supply's positive and negative leads.
How do you get camera off of stand by?
Ans: yess when camera on,then i click in power of mobile..then off.
Best wireless security camera?
Wireless Cameras are relatively expensive and are not as reliable as wired systems. Most wireless systems are Line of Sight (LOS). Remember that wireless security cameras require power to operate. So even though by going with a wireless solution you can eliminate the need for coaxial cable for video transmission, you still have to wire the camera to a power source. Keeping that in mind it depends on what you want from your camera. How far away will the camera be from what you are trying to record? Will the Camera be inside or outside? Does it need to record color or can it be in black and white? Do you want to be able to remotely make the camera zoom in or change the viewing angle? There are a lot of questions to answer before deciding what the 'best' wireless camera is. To help answer some of those questions check out this guide to help you figure out what you are looking for in a security camera. http://www.apexcctv.com/CCTVBuyerGuide.aspx
What is Connecting rods sewing machine and uses?
A rod that transmits motion or power from one moving part to another, especially the rod connecting the crankshaft of a motor vehicle to a piston. Also called pitman.
What type of power supply runs computa fc-62c security camera?
It would be appropriate to connect a 24 volt ac power supply to the terminals marked 'AC 24V'. Since the power consumption of this camera is listed as '4 watts or less' then a 500 mA supply would be more than adeqUate.
What must be disconnected from a circuit under test before connecting the ohm meter to the circuit?
You must always disconnect the power supply from the circuit before connecting an ohmmeter.otherwise the meter may be damaged.
Before connecting the power generation equipment into the primary series circuit you should?
functional checks
What does the power switch on a camera do?
the power switch on a camera turns on or off the camera.
How do you transfer pictures from your camera to your computer?
Your first step should be connecting your camera to the computer, usually via a USB connection with a cord that comes with the camera. From there you should power up the camera and follow the popup instructions that should soon start to appear. Otherwise go into My Computer and look for a new drive to show up with your pictures in it.
What features can be found on a typical analog camera?
a typical analog camera has complex features 12 v dc power supply lens chip completely wired system with one female video and power connector
The balance of power system broke down during after or before?
Before
With what kind of energy does a battery power a camera?
Chemical and electrical energy are used. They power a camera.
How does one install a wireless camera system?
There are several guides on the internet such as youtube teaching you how to install camera observation system. Visually, it gives you a better understand of your system and teachs you how to operate the system.
Kinect on old xbox 360 120gb?
Yes, you can. The notion of "Kinect Ready" simply means that the newer XBOXes will be able to run the camera/mic with power directly from the XBOX. My understanding is that you can set it up to the old one by connecting power cord to wall outlet.
Why is it a good idea to install a ribbon cable before connecting power to drives?
Ribbon cables are difficult to work with and it is never a good idea to install cables on a device when it has power running to it. Components could short and be damaged or the technician could be damaged.
What component do you remove to isolate the secondary distribution center transformer before connecting the primary power cables?
the electric fusible disconnect EDF switches
Can one use a three wire cable or the same ground wire when sending power to a video camera and receiving a signal from that camera?
It's possible, but it depends a lot on the electronics of the camera and whether or not it's being operated by an AC or DC power source. In fact, it's even possible to send the video over a two wire system, such as the power supply's positive and negative leads.
