0
Apply it the same as any other sheet metal. Just make sure it is supported from the back; ie., if off the vehicle...put it back on and begin working. If off and no car around....use a wooden saw horse (tends to work best), place over top and secure with wood screws. If you try shaping on unsecure sheet metal, you create more damage than to begin with.
What else can I help you with?
How do you shape bondo and is there a type of Bondo to use on plastic car bumbers?
While it is still setting up, it can be carved to get a general shape, then it is sanded. Apply in thin layers up to 1/4 inch for large areas. To fill in large gaps or to build shapes it can be put on a sheet of plastic or cardboard and held in place until it sets. There are epoxy fillers for bumpers, but if there is much damage it is usually better to replace the cover.
What are the small racing stripes on the fender of a car called?
Pin stripes.
Is there any way to remove bondo?
Besides sanding, grinding and scraping, you can remove Bondo from your clothes and other porous items with fingernail polish remover (acetone). Test the cloth in an inconspicuous spot before you try this because it will also dissolve some fabrics. You may need to let it soak for a while to soften it enough. Acetone evaporates very easily and is flammable so it would be best to do this outdoors. ZipStrip will also remove bondo but it is even more likely than acetone to destroy fabric...Test FIRST!
How can you repair holes in metal?
thin material holes can be welded and ground flush, think material can be threaded and plugged. Bondo works, too.
Fender off a 1969 valiant will it fit a 1969 dart?
I doubt very much that the fender is the same as the darts.
How do you get bondo smell out of car?
Let bondo air out, colder weather will make it take longer.
What are tips for repairing a car with Bondo?
Remove all foreign material, i.e., rust, paint, etc. Apply bondo to clean, rough metal only. Make sure metal is roughened to ensure adhesion of bondo to metal. Begin shaping, sanding, just after bondo is set up, don't leave too long, will be difficult to sand. Apply more bondo, to the sanded bondo, if needed, sand again - apply primer just prior to touch out glaze. 1. Use only fresh Bondo, not some that was opned last year. 2. Don't mix a large amount at one time. It will harden before you have a chance to apply. 3. Make sure your Bondo and hardener are well mixed. 4. Once you are shaped and sanded, get primer on it right away. Bondo and other fillers hold water. 5. Don't leave primer on too long without painting, it holds water as well. 6. When you're are shaping and sanding, WEAR A MASK. The dust can ruin your lungs.
What is bondo made out of?
Bondo is a brand of automotive body filler that is primarily made of polyester resin and talc. It is used to repair dents, scratches, and other imperfections on car surfaces.
How can I effectively use wood bondo for repairing damaged wood surfaces?
To effectively use wood bondo for repairing damaged wood surfaces, follow these steps: Clean and prepare the damaged area by removing any loose or damaged wood. Mix the wood bondo according to the manufacturer's instructions. Apply the wood bondo to the damaged area, shaping and smoothing it as needed. Allow the bondo to dry completely before sanding and painting or staining as desired.
When would you use bondo on the glass of a car?
It is not my intent to be sarcastic or or derogatory ...but I can't accept this as a legitimate/serious question. The Bondo brand of body putty is for metal parts, not glad. There is no situation that would ever call for such a use.
What a sentence using the word fender?
A car fender
Where is the fender of the car located?
The fender of the car is located on the front sides of the car. The fenders sit right above the tires.
When was Bondo Shoshitaishvili born?
Bondo Shoshitaishvili was born in 1939.
How can I use Bondo to repair wood effectively?
To effectively repair wood using Bondo, start by cleaning and sanding the damaged area. Mix the Bondo according to the instructions and apply it to the damaged area, shaping it as needed. Let it dry completely before sanding it smooth. Finish by painting or staining the repaired area to match the rest of the wood.
How do you use fender in a sentence?
'The fender on my car got smashed in the wreck I was in.'
Mix bondo with water?
Mixing bondo with water is not recommended, as bondo is meant to be mixed with a hardener to cure properly. Using water can compromise the strength and overall quality of the bondo. It is best to follow the manufacturer's instructions and mix bondo with the appropriate hardener for best results.
What are the best techniques for using wood filler bondo to repair damaged wood surfaces effectively?
To effectively repair damaged wood surfaces using wood filler Bondo, follow these techniques: Clean the damaged area thoroughly to remove any debris or dirt. Mix the Bondo according to the manufacturer's instructions. Apply the Bondo to the damaged area, using a putty knife to smooth it out. Allow the Bondo to dry completely before sanding it down to a smooth finish. Prime and paint or stain the repaired area to match the surrounding wood.
