0
How do you make the 'brake' light go off after having replaced the low-fluid sensor in the master cylinder on a 2001 Grand Am SE?
Wiki User
∙ 8y ago
Make sure the float is floating and clean.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
You drive a Mitsubishi Pajero engine 4D45 Its clutch master leaked you replaced the parts inside the master pump After 10000km the leak comes back What if your comment please?
did you hone the cylinder before you replaced the parts
If a master cylinder is bad how much damage could happen when you continue to drive on it?
Well if you continue to drive it with a defective master cylinder, your brakes will eventually fail, and you can end up having a wreck and possibly killing yourself or someone else. Is that enough damage for you? Replace the master cylinder and don't be an idiot.
What is the best method for bleeding the master cylinder yourself at home?
Last time I replaced a master cylinder I got a kit with it. before you hook up the brake lines you screw in 2 zerts connect plastic tubing to them and run them into the fluid reseviors then pump the brakes until no bubbles come through the plastic lines
Where does clutch fluid go?
There is a smaller master cylinder next to the brake master cylinder. The clutch uses brake fluid also. If you mean where does it go if it is low, the slave cylinder on the transmission is probably leaking.
How hard is it and How do you change master brake cylinder on 1999 Chevrolet Suburban?
The master cylinder on a 1999 suburban is pretty easy to change. Under the dash, disconnect the clutch pedal from the cylinder rod. disconnect the brake lines from the master cylinder and allow to drain into a container. Unbolt the cylinder and remove. Install the new cylinder and connect the lines and rod back up. Add new fluid, and bleed the slave cylinder to finish the installation.
Why is it hard to shift into first gear second gear and reverse after having the clutch replaced as well as the master cylinder and slave cylinder?
bleed your clutch..that may be the problem
How do you know when the clutch master cylinder is gone in a 1995 escort?
Whenever you are having a problem with the clutch disengaging the engine from the transmission it is advisable to bleed the clutch slave cylinder. If the clutch can't be operated by bleeding the slave cylinder then the clutch master cylinder is gone and should be replaced.
Should you replace your clutch master cylinder when replacing clutch?
At least the slave cylinder. The clutch master cylinder can be replaced at any time.
How long does it take to change a brake master cylinder on 306?
Master Brake cylinder replaced and lines bled-how long?
When do you bleed your clutch?
after the clutch master cylinder has been replaced.
How much does it cost to replace the master cylinder in the clutch of a Ford Focus 2005?
I'm having mine replaced today and it's costing £165.
Do you have to replace the master cylider if the slave cylinder has been replaced in a 1993 Saturn?
The Slave Cylinder and the Master Cylinder control totally different systems. The Slave has to do with the clutch, and the Master has to do with the brakes. They have nothing in common.
You just had your master cylinder replaced on your 95 wrangler.4 cylinder manualNow you are having problems shifting gears Could this be related?
Nope, not unless when removing master cylinder somehow the slave cylinder got bumped a bit too hard. Slave cylinder is the smaller one that the clutch pedal uses to push in and out the throwout bearing allowing for manual shifting...
When a master cylinder is how can you tell?
A master cylinder should be replaced when it can no longer provide the pressure needed for the brakes to operate. You can tell it is failing when the pedal becomes soft.
I have bled the slave cylinder on my 240sx and replaced the clutch master cylinder and my 240sx will still not shift into gear. What else can I check?
If you did not bench bleed the master, you need to do that.
How do you replace clutch master cylinder Chevy s10?
The clutch master cylinder on a Chevy S10 is replaced by disconnecting the metal lines, unscrewing the retaining bolts, and removing it from the housing. A new master cylinder can then be put into place and reattached.
What does it mean when there is fluid dripping from the master cylinder and the petal goes all the way to the floor?
It means your master cylinder needs to be replaced or rebuilt. The seals inside the cylinder can go bad and cause this to happen.
