answersLogoWhite

0

also make sure the e-brake is disengaged From the rear of the backing plate, remove the brake shoe adjusting slot cover and insert a screwdriver or a brake shoe adjusting tool and back off the star wheel by prying downward with the tool. Until you have removed the pressure from the brake shoe's then pull the drum off. [http://www.themotorbookstore.com/rodeo.html I would also advise getting a Manual] it make sure you get the Brake Job done right.
You don't want to KILL Someone, yourself included because of a missed step. Good Luck and Remember.
Change Your Mind, Not Your Oil.
Use the First In Synthetic Motor Oil's.
See My Bio For more information.

User Avatar

Wiki User

18y ago

What else can I help you with?

Continue Learning about Art & Architecture

How do you replace a brake light on a 2003 Toyota RAV-4?

Open trunk and remove screws that secure light assembly to car. Pull assembly straight back to remove from car. Remove the dead light and replace with proper new light. Install in reverse order of removal.


Where is the fuse box on an 1987 Isuzu pup?

under the hood on the driver side in front of the brake booster


How do you install brake pads on a 1992 Aerostar?

# Release the parking brake # Remove the cowl trim panel from the left side of the drivers compartment for access to the parking brake pedal # Pull back on the parking brake cable toward the control assembly (parking brake) and insert a 5/32 inch drill bit into the control actuator to lock the assembly into position # Its actually easier to pull the parking brake cable from under the vehicle but you will need an assistant to help you do this way. # Loosen the rear wheel lug nuts and raise and support the truck # Remove the brake calipers and the brake discs # Detach the parking brake cable from the actuator arm # Clean the parking brake assembly with brake cleaner # Remove the brake shoe retracting spring # Remove the adjusting screw spring and remove the adjusting screw # Remove the hold down springs from the shoes # Remove the parking brake shoes from the actuator


Where is the emergency brake in the 2000 Isuzu Rodeo?

On the rear wheeels. some have a special drum inside the rotor and some use the caliper.


How do you change the brake light located in the middle of the trunk lid 2000 dodge neon?

You can access the middle brake light from the inside of your 2000 Dodge Neon cargo compartment. Remove the brake light wiring harness. Remove the brake light retaining bolts. Reverse the process to install the new brake light.

Related Questions

How do you change brake lights on 1996 Isuzu Rodeo?

remove the 2 screws from the red plastic and gently pry the red cover off.


You are trying to change a rear brake bulb on a 1999 Isuzu Rodeo you have already removed the 2 screws but something it still not allowing you to remove the cover?

There is a third screw between the brake light and the bumper.


How do you remove the right side rear backing plate of a 1992 Cadillac Sedan DeVille?

remove wheel remove brake drum remove brakes disconnect brake fluid line remove parking brake cable from backing plate remove four bolts attaching backing plate to axle housing remove wheel remove brake drum remove brakes disconnect brake fluid line remove parking brake cable from backing plate remove four bolts attaching backing plate to axle housing


How does the rear brake drum come off of a 1999 Isuzu NPR?

To remove the rear brake drum from a 1999 Isuzu NPR, first ensure the vehicle is securely lifted and supported on jack stands. Remove the wheel and tire, then locate the retaining bolts or screws on the drum; if present, remove them. If the drum is stuck, tap it gently with a hammer to loosen it, and use a brake adjustment tool to back off the brake shoes by turning the adjuster wheel. Once loose, the drum should slide off the wheel hub.


How do you change the brake lights on a 2004 Rio Cinco?

Remove inside panel and remove the screws. If there are no screws then pry it out with a screwdriver.


How do you remove third brake light s10?

Remove the two screws in the lens. You can remove the entire assembly once you do this.


How do you remove the brake caliper on a 94 mercury villager?

Remove the two slider screws that hold it in place.


How do you access the panel to replace a brake light on a 1998 Isuzu Rodeo?

You have to remove the entire light assy. There are some screws that are hard to find but they are there. accessed from the outside 3 in all use a medium length Phillips screwdriver. GoodluckJoe


How do you remove the door handle on a 2005 Kia Spectra?

which door, most of the time you remove the door panel screws and then pull hard you will not brake it if you pull and look you can see plastic keepers attaching the door panel they will pull out but feel like you will brake something, then remove clear plastic car full not to tare then use a flash light you will see the bolts or clips on the out side door handle, or look inside and see door latch remove screws from side of the door with it open. hope this helps work on kia for 4 years.


How do you change a brake light on a 1998 Chevy Camaro?

You will need to remove the 1998 Chevy Camaro brake light wiring harness. Remove the brake light retaining screws. Reverse the process to install the new brake light.


Replacing brake light bulb?

Lift the rear hatch you will see 2 torx screws. Remove the screws and slide out the lens. remove corresponding bulb/socket, replace and reinstall.


How do you replace the third brake light in a F150 1995?

you remove plastic red/white cover with 2 screws and remove bulbs.