0
You need to remove the venturi from the jet pump housing by removing the steering cable and then the reverse cable (if applicable) Then remove the four nuts holding the pump housing to the seadoo. You will need to pull on the housing to remove the drive shaft from the impeller pinion, just pull staight back. Once the Pump housing is removed, there is a tool available from Seadoo, with 18 splines in it. Insert tool, and use a ratchet or impact wrench and unscrew the impeller from the craft. Hope this helps.
What else can I help you with?
Yamaha wr correct way to remove water pump impeller?
Remove the side case and the water pump. Remove the right side case, and remove the impeller and shaft. Holding the back side of the impeller shaft with a wrench on the flat spots, you can now twist the impeller off.
What song is this it goes like I think walking (I think its walking) (something) in love (something I can't hear but it matches doo doo doo) walking (something) in love doo doo doo and its a boy?
*boy and girl duet
What is the gas oil mix for a 1985 ski doo citation?
Its Either 40:1 or 50:1 but you should consult your local Ski-Doo dealer just to be sure
What rodents start with the letter D?
degu
How do you change impeller on 5.7l mercruiser?
Please Note I am not a mechanic. I had the same problem and found this answer: Tools and materials required:Socket wrenches, 9/16th box wrench, torque wrench capable of measuring 10 foot pounds, Loctite for threads, Vaseline Petrolem Jelly, and of course a water pump replacement kit that includes the impeller, plastic housing, stainless steel back plate, two gaskets, and new bolts. Warning: The water pump is below the water line and when the lines to the pump are removed water will pour into the boat. I had my boat out of the water when I changed the impeller. Procedure: Loosen the idler pulley and remove the drive belt. Make note of the way the belt wraps around the various pulleys. Remove the two 9/16th bolts that hold the pump and bracket to the engine. You will now have enough room by pulling the pump out of the front of the engine to get to the two hose clamps on the water hoses. Mark the two hoses so you get them installed correctly. Loosen the two hose clamps and pull the hoses off the pump. I took the pump to my garage so I had access to a vise and wire brush. The wire brush was helpful in cleaning the bolt threads to make it easier to remove them. Mark or make note of proper position of the bracket on the pump. Remove the three nuts holding the bracket to the pump. Remove the 5 bolts holding the plastic pump to the metal end. Lightly coat the inside of the pump housing and the new impeller with the Vaseline. The Vaseline protects the new impeller as it will run dry for a few seconds when first starting the engine. Install the impeller in the new pump housing. Install the smaller gasket around the pump shaft, and install the new wear plate. Install the new gasket on the plastic pump, and then the plastic pump to the front half of the pump. Coat the new bolt threads with Loctite. Install the two shorter bolts and just snug them down. Install the remaining three long bolts after coating with Loctite. Tighten all boats in a cris-cross pattern. I set my torque wrench to 50 inch pounds, tightened all bots then increased the torque setting on the wrench till I reached 110 in. lbs. or just over 9 ft. lbs. Install the mounting bracket to the pump. Hold the heads of the bolts when tightening the nuts on the mounting bracket. Reverse the order of installing the pump back onto the motor. Install the drive belt and set the tension with the idler pulley. Make note in your maintenance log of the date and number of hours on the motor when you changed the impeller. Total time involved was about 2 hours. This is a maintenance that can be handled by most weekend wrench-turners.
How would i un seize a 97 xp sea doo 2 stroke motor?
remove the jet pump and insert the impeller tool into the pto flywheel. Remove spark plugs and put some lubricant down the spark plug hole and try to turn the engine over with a breaker bar on the impeller tool.
Yamaha wr correct way to remove water pump impeller?
Remove the side case and the water pump. Remove the right side case, and remove the impeller and shaft. Holding the back side of the impeller shaft with a wrench on the flat spots, you can now twist the impeller off.
When was Sea-Doo GTX created?
Sea-Doo GTX was created in 1993.
How do you change the impeller on a 9.8 mercury outboard?
The impeller on a 9.8 Mercury outboard boat motor can be easily changed. Remove the retaining bolt. The impeller will come off. Reverse the process to install the new impeller.
How do you remove the impeller on a Mariner 2 hp?
To remove the impeller on a Mariner 2 hp outboard motor, first, ensure the engine is off and cooled down. Disconnect the water intake and remove the lower unit by unbolting it from the midsection. Once the lower unit is detached, locate the impeller housing, remove its screws, and carefully lift out the impeller. Be cautious not to damage the housing or the drive shaft during this process.
Where is the fuse box on sea-doo?
The fuse box on a Sea-Doo is typically located under the front storage compartment or in the rear storage area, depending on the model. To access it, you usually need to remove a cover or panel. It's important to consult your specific Sea-Doo owner's manual for the exact location and instructions, as it can vary by model and year.
How do you change the impeller on the water pump on your 35 horsepower evinrude outboard boat motor?
First, remove the lower unit (there is a housing for the water pump). The drive shaft goes through the housing and turns impeller. Remove the housing, the impeller is on the shaft. Install the new impeller. When replacing the housing, turn the drive shaft clockwise to make it slide down over the impeller.
Which is better Sea Doo or WaveRunner?
Don't ever buy a Yamaha always go with sea doo. there the BEST!!!!!!!!!!!
How do you repair eska water impeller?
To repair an Eska water impeller, first, remove the impeller from the lower unit by unscrewing the retaining screws and gently pulling it out. Inspect the impeller for any signs of wear or damage, such as cracks or missing blades, and replace it if necessary. Clean the area where the impeller sits to remove any debris or old sealant, then lubricate the new impeller with a compatible grease. Reassemble the components, ensuring everything is securely fastened and properly aligned before testing the motor.
Where is the Volvo penta impeller located?
The impeller in a Volvo Penta is located inside the water pump. You will need to first remove the water pump to access it.
How do you remove the impeller from the engine shaft from a wood chipper shredder?
To remove the impeller from the engine shaft of a wood chipper shredder, first ensure the machine is completely powered off and unplugged for safety. Remove any protective covers and locate the impeller mounting bolts or set screw; use the appropriate tools to loosen and remove them. Once detached, gently pull the impeller off the shaft, being careful not to damage any surrounding components. If it’s stuck, tapping it lightly with a rubber mallet may help to free it.
How do you remove impeller on godwin pump CD 150?
To remove the impeller on a Godwin CD 150 pump, first ensure the pump is powered off and disconnected from any power source. Next, remove the pump casing by unscrewing the bolts that secure it, and then carefully lift it off to access the impeller. Use a suitable tool, such as a puller, to gently extract the impeller from the shaft. Make sure to follow any specific manufacturer guidelines or safety precautions during the process.
