0
To remove the intake manifold on a 2004 Mitsubishi endeavor, you should take it to a mechanic. An authorized dealer will also fix it for you.
What else can I help you with?
How do you remove lifters from A 1998 Chevy 454?
They are under the intake manifold.
How do you replace the whole head gasket set on 1994 sidekick 4wd?
Remove the intake manifold, exhaust manifold, and then remove the head. Scrap off the old gasket and install a new one. Reinstall the head and Torque the head bolts in the proper sequence. Reinstall the intake and exhaust manifold torque the bolts to the proper torque. This is a major repair and not for a novice to try.
Where is the EGR valve located on a 1997 Mitsubishi Mirage?
Check the emission label usually located on the top of the radiator or on the core support just in front of the radiator. You will see a diagram of all the vacuum lines and emissions equipment. Generally-the EGR valve is located near the throttle body.
How do you change the starter on a 1992 deville 4.9L?
It's quite a process that shouldn't be attempted without the factory service manual. Basically, you need to remove the intake manifold to get to the starter. After the intake is off, it's easy to do. But the factory service manual would have all the info you need to safely and correctly remove the intake without damaging any of the delicate fuel injection parts.
How do you remove a broken stud from the water outlet neck on an aluminum intake manifold?
Are you handy with a center punch, and a drill? If so, the best way to do this is to drill a hole in the center of the stud, and along with penetrating oil, an/or heat from a torch, use an easyout to extract the broken stud from the intake.
How do you remove the intake manifold on an eclipse?
Basically you remove the throttle body, fuel rail, and anything else that is plugging into it, then unbolt it. You need to get a shop manual however, because there is a specific bolt pattern you need to use to avoid damage.
How do you change intake manifold on Isuzu trooper?
remove intake manifold.
How do you know when to replace the fuel pump on a 1988 Mitsubishi pickup?
you have to remove the studs, or remove the entire intake manifold! when you do finally get it off replace the studs with bolts.
How to Remove a intake on a 2002 Mitsubishi diamante?
To remove the intake manifold on a 2002 Mitsubishi Diamante, first, disconnect the battery and remove any components obstructing access, such as the air intake, throttle body, and associated hoses. Then, unbolt the intake manifold from the engine, taking care to label or keep track of any bolts and connectors. Carefully lift the manifold off, ensuring no debris falls into the engine. Finally, inspect the gasket and surfaces for damage before reinstalling or replacing any necessary parts.
How do you remove the rotors on a 2004 Mitsubishi Endeavor?
i have 2006 endeavor changing brakes do i have to remove the two screws in the rotor to remove so i can have resurfaced
Where is a 5.3l v8 knock sensor?
There is 2 of them. and they are under the intake manifold. You will have to remove the intake manifold to get to them.
How do you remove intake manifold gasket in 1993 Benz 190e?
Remove the intake manifold retaining bolts from your 1993 Mercedes-Benz manifold. Remove the old manifold gasket. Clean the surface and put the new gasket on.
How do you remove a vl commodore head gasket?
Remove the intake manifold, exhaust manifold, and then remove the head.
How do you Change spark plugs for 2005 Mitsubishi galant V6?
You must remove the entire intake manifold for you to have access on the three spark plugs located underneath it. it is advisable that a qualified Mitsubishi technician should do this.
How to replace the Intake manifold gasket on a 1996 Chevy Astro?
Remove the intake manifold retaining bolts from your 1996 Chevy Astro Van. Remove the manifold gasket and clean the surface. Reverse the process to install the new intake manifold gasket.
How do you change a door handle on a 2004 Mitsubishi Endeavor?
To change a door handle on a 2004 Mitsubishi Endeavor, remove the 2 screws of the face plate. Then remove the 2 screws on the knob plate. Remove the door handle and replace with new.
Where is starter located on 2004 Honda accord?
under the intake manifold. you have to remove all intake hose and intake manifold itself to get to the starter.
