answersLogoWhite

0

If you look a the wiper where it is attached, you will see a little sort of spring clip, when you push on this clip with a small screwdriver, it will release. There are many different types, so if this one is yours, it is very easy. The new one will just lock in when you push on it.

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Art & Architecture

Where is the windshield wiper control module located on a 1993 Pontiac Transport?

The 1993 Pontiac Transport windshield wiper control module is located on the firewall in the engine compartment. The windshield wiper control module will be on the passenger side of the firewall.


Can you locate the front wiper fuse in a 1999 ford expedition?

You can find your 1999 Ford Expedition front windshield wiper fuse in the fuse box. The windshield wiper fuse will be in the second column, fourth from the top.


Where is the wiper relay on a 1998 ford Crown Victoria?

The 1998 Ford Crown Victoria windshield wiper relay switch can be found on the firewall in the engine compartment. The windshield wiper relay switch will be on the passenger side of the firewall.


How to replace a 1999 f-150 windshield motor?

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


Why do the windshield wipers on a 1993 Mercury Grand Marquis LS stop in up position when shut off but work fine otherwise?

the windsheild wiper motor clutch/windlatch is broken

Related Questions

How do I replace the windshield wiper switch?

How do I replace the windshield wiper switch?


How do you replace a windshield wiper blade on a 1999 grand mercury marquis?

You take it to autozone and they will show you


How do you repair a leek in the windshield wiper hose on a Mercury Grand Marquis LS 2002?

Replace the hose.


How do you replace the rear windshield wiper in a 2000 mercury mountaineer?

Raise the wiper blade and hold. Pull the release on the bottom of the blade and wiggle it off.


My windshield wiper goes off the windshield?

Replace the locking tab on top of the wiper


What size windshield wiper blades are used on a 1993 Mercury Villager?

The 1993 Mercury Villager takes 22" replacement windshield wiper blades on both sides front.


How do you replace wiper switch l200 series?

2001saturn l200 how to replace a windshield wiper switch


How do you replace windshield wiper motor for 1994 mercury villager?

To replace the windshield wiper motor on a 1994 Mercury Villager, start by disconnecting the negative battery cable for safety. Remove the wiper arms by loosening the nuts at the base and gently pulling them off. Next, take out the interior panel covering the wiper motor, disconnect the wiring harness, and unscrew the motor from its mount. Finally, install the new motor, reconnect the wiring, and reassemble the wiper arms and interior panel.


How to Replace a Toyota Camry windshield wiper switch?

? wiper switch toyota camry 1999 replace


How do you fix windshield wipers on a Volvo 940?

To fix windshield wipers on a Volvo 940 try using new wiper fluid and cleaning the windshield and wiper blades before you replace the blades. It is also important to replace wiper blades regularly.


How do you replace a windshield wiper motor on a 1998 Mitsubishi mirage?

How to replace wiper motor on a 1998 montero sport mitsubishi


How do you replace a Kia Sportage front windshield wiper motor?

No