0
How do you replace a crankshaft position sensor or where can you find a step by step guide?
Wiki User
∙ 8y ago
You can most likely find a guide at a local auto parts store like NAPA or Autozone, try Autozone first or Advanced Auto Parts if you have one, they are usually pretty good about carrying guides like that.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
If the plastic guide on a shifter transmission cable is broken do you have to replace the entire cable?
You generally can't replace the guide without replacing the cable. If the transmission still shifts easily, you don't need to replace the cable immediately (as in, it is not an emergency) however you should plan to replace it as soon as you can. yes you do there is no getting around it, sorry
Where is the coolant temperature sensor mounted in a 2004 Isuzu Ascender with a v-6 engine?
If it's anything like the '05 V-6, it's located towards the front of the (driver's side) engine block. A diagram from Autozone repair guide can be found here: http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80382f1e. Gonna replace mine, along with thermostat this week. BTW, is your check engine light on, and giving you a code saying that either the coolant is low, or thermostat/coolant temperature coolant sensor is bad? Best of luck.
Why does an engine valve need to be removed from the cylinder head?
An engine valve normally needs to be removed from the head for a valve job, or to replace other parts related to its operation like the spring or valve guide. This is normally done when the engine has a poor seal from the valve/valve seat or oil consumption caused by the vavle guide.
My sunroof on my 99 Plymouth neon only budjes up then down?
Need to know what the problem is. leaking? not opening? etc. I had a similar problem with my neon. The track guides are very fragile and break often. There is just a wire cord that pushes and pulls on the guide to open and close the sunroof and the attachment breaks easily. the only fix is to replace the guide. The only place i have found new guides is at http://www.sunroofdoctor.com/9799neon.htm
How much is timing belt?
after calling around the cost seems to be between $350- $500 depending on the garage rates. it takes between 3 - 5 hours and the belt costs between $60 - $100 which is included in above estimates
How do you replace crankshaft sensor on Chrysler sebring 2000?
CRANKSHAFT POSITION SENSOR - 2.5L REMOVAL Remove speed control servo from driver's side strut tower. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor Pull crankshaft position sensor straight up out of the transaxle housing. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector. INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor. NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque. Connect crankshaft position sensor electrical connector to the wiring harness connector. Attach connector to heater tube bracket. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque. extra steps for Simplification added by Billebones@AOL.com: Also: Jack up car and put it on jackstands Remove left front tire, remove plastic shield covering the battery then use a long extension with a 10mm socket to remove and install the bolt holding the sensor right over the top of the axle, this definitively simplifies getting at the bolt, if you have someone up on top to guide it back in it will be even easier. I did not remove heater tube bracket and I plugged it together before I put the sensor into the bell housing
How do you replace a Crank Position Sensor on a 1992 Oldsmobile Regency 98?
It takes a special tool. I got mine from Autozone and had a guide from them on how to replace it. You'll have to remove the belt and harmonic balancer and access it through the passanger side front tire.
Where is the cam sensor located on a 2000 Mercury Villager sport?
The cam sensor is located in the distributor. The cost of a distributor is about $250.00 and up. get the cam sensor checked first, then if needed, replace. Use a Haynes Manual or something else to guide you thru the replacement process. It's easy to do.
Where are the bank 1 sensor 1 and bank 2 sensor 1 on a 2001 Bravada?
Refer to your Chilton's repair guide/get a Chilton's repair guide.
What are the timing marks for a 1997 Ford F150 4.6 liter engine?
{| |+ Special Service Tool(s) |- | Cam Positioning ToolT91P-6256-A Cam Positioning Tool AdaptersT92P-6256-A Camshaft Holding ToolT96T-6256-B Camshaft Positioning ToolT96T-6256-AR Removal # Remove the engine front cover; refer to the procedure in this section. # Remove the (A) crankshaft sensor ring from the (B)crankshaft (6303).# On WEP engines, use the (A) Camshaft Positioning Tool to position the (B) camshaft.# on REP engines, rotate the crankshaft until both camshaft keyways are 90° from the cam cover surface. On REP and WEP engines, make sure the copper links line up with the dots on the camshaft sprockets.# On REP equipped engines, install the (A) Cam Positioning Tool and the Camshaft Positioning Tool Adapters on the (B) camshaft.# On WEP engines, install the (A) Camshaft Holding Tool on the (B) camshaft.# Remove the (A) LH timing chain tensioner bolts and the (B) LH timing chain tensioner.# Remove the (A) RH timing chain tensioner bolts and the (B) RH timing chain tensioner.# Remove the LH and RH timing chain tensioner guides from the dowel pins.# CAUTION: At no time, when the timing chains are removed and the cylinder heads are installed may the crankshaft or camshaft be rotated. Severe piston and valve damage will occur. Remove the RH and LH timing chains and crankshaft sprockets. ## Lift RH timing chain off of the camshaft sprocket and slide the timing chain and crankshaft sprocket off of the crankshaft. ## Lift the LH timing chain off the camshaft sprocket and slide the timing chain and the crankshaft sprocket off of the crankshaft.# On REP engines, remove the chain guides. ## Remove the LH timing chain guide bolts. ## Remove the LH timing chain guide. ## Remove the RH timing chain guide bolts. ## Remove the RH timing chain guide.# On WEP engines, remove the chain guides. ## Remove the LH timing chain guide bolts. ## Remove the LH timing chain guide. ## Remove the RH timing chain guide bolts. ## Remove the RH timing chain guide.Installation CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result. # Compress the timing chain tensioners (6L266). ## Release the lock assembly on the timing chain tensioners. ## Compress the timing chain tensioners.# Install the retaining pins.# Check the following components for part number orientation.! valign="bottom" | Item ! valign="bottom" | Part Number ! valign="bottom" | Description | 1 6268 Timing Chain/Belt (RH) 2 - RH Timing Chain Guide (WEP) 3 6L253 Timing Chain Tensioner Arm (LH) 4 6L266 Timing Chain Tensioner (LH) 5 6268 Timing Chain/Belt (LH) 6 - LH Timing Chain Guide (WEP) 7 6K297 Timing Chain Guide, (REP) RH 8 6L253 Timing Chain Tensioner Arm (RH) 9 6L266 Timing Chain Tensioner (RH) 10 6K297 Timing Chain Guide, (REP) RH# On REP engines, install the timing chain guides. ## Position LH timing chain guide. ## Install and torque the LH timing chain guide bolts. ## Position the RH timing chain guide. ## Install and torque the RH timing chain guide bolts.# On WEP engines, install the timing chain guides. ## Position the LH timing chain guide. ## Install and torque the LH timing chain guide bolts. ## Position the RH timing chain guide. ## Install and torque the RH timing chain guide bolts.# Install the timing chain/belts (6268) and crankshaft sprockets (6306). ## Slide the (A)crankshaft sprocket onto the (B) crankshaft, aligning the copper link on the timing chain/belt with the dot on the crankshaft sprocket. ## Position thetiming chain/belt over the camshaft sprocket, aligning the copper link with the dot on the camshaft sprocket.# Make sure that the (A) copper marks on the timing chain/belts are lined up with the corresponding dots on the crankshaft and camshaft sprockets.# Make sure that the (A) camshaft sprocket keyway is 90° from the (B) cam cover mounting surface.# Make sure that the (A) RH timing chain sprocket is on the front of the (B) LH timing chain sprocket with the hubs facing each other.# Position the LH and RH timing chain tensioner guides on the dowel pins.# Position the RH timing chain tensioner and install the timing chain tensioner bolts.# Position the LH timing chain tensioner and install the timing chain tensioner bolts.# Remove both the RH and LH retaining pins from the timing chain tensioners.# On REP engines, remove (A) Cam Positioning Tool and the Camshaft Positioning Tool Adapters on the (B) camshaft (6250).# On WEP engines, remove the (A) Camshaft Holding Tool from the (B) camshaft.# On WEP engines, remove the (A) camshaft positioning tool from the (B) camshaft.# Install the (A) crankshaft sensor ring on the (B) crankshaft.# Install the engine front cover; refer to the procedure in this section. |}
How do you replace the MAP sensor in a 1996 Dodge Intrepid 3.3L?
View Repair Guide http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?partName=Manifold+Absolute+Pressure++MAP++Sensor&pageId=0900c1528006ab35&partId=0900c1528006ab35#hd1-1-3
how can a gps guide you if your lost?
The gps global positioning system can guide you by locating your positon and then it would guide you to the position that you had requested to get to.
How do you replace the distributor on a 1987 Chevy Celebrity 2.8 liter engine?
If you go to www.autozone.com and register for free, you input your car info and look up a part. After you get to the page with the part and prices listed, look to the right and you will find a section that says "YOUR RIDE. YOUR GUIDE." When you click this, you will get the actual pages from the repair manual that show you how to replace this part. I use it constantly and love it that I get the manual info without shelling out the $25 for the hard copy. That is a valid general suggestion. However there is no distributor on your 1987 Celebrity. It has an ignition module and a crankshaft sensor controlled by the ECM.
Where can you find a guide on how to replace PCI SATA cards?
Someone can find a guide on how to replace a PCI SATA card from a number of websites such as CNET. CNET has several in depth guides on how to replace PCI SATA cards located under its how to section.
How do you replace a cv joint in a Honda Odyssey?
Much better to replace the whole axle, look at www.happywrenching.com for a guide on how to replace an axle in a Honda Odyssey
If the plastic guide on a shifter transmission cable is broken do you have to replace the entire cable?
You generally can't replace the guide without replacing the cable. If the transmission still shifts easily, you don't need to replace the cable immediately (as in, it is not an emergency) however you should plan to replace it as soon as you can. yes you do there is no getting around it, sorry
How do you replace the drive and variable speed belts on MTD 14AZ808K131?
Set the parking brake and disconnect the spark plug wire. Remove the cutting deck and the battery. Loosen the pulley and remove the upper belt. Remove the belt guide and the belt keeper. Loosen the bolt on the crankshaft pulley. Remove the lower drive belt.
