0
6 or 8 it varies car to car.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How many bolts hold on an alternator for a 2000 Ford Focus?
2
What kind of bolts hold the ignition control module in a 1987 Ranger 2.3L?
5.5mm bolts are the kind of bolts that hold the ignition control module in a 1987 Ranger 2.3L. However, 5.0mm bolts may also work.
How do you remove a fan clutch on a 1997 S10 pickup 2.2L?
The fan clutch on a 1997 S10 has a bolt on the center of the front. Remove the bolt while holding the clutch still. There is a special tool to grab the clutch fan from the rear to hold it while removing the bolt.
How hard is it to replace the rear sway bars and links?
Not hard at all. 6 bolts for the sway bar, and depending on how many links 8 bolts if it is a 4 link, figure 2 bolts per link. ues jack stands to hold the rear axel in place and do it one link at a time. The sway bar cones off in one piece so do that last.
Where is the 2000 Toyota Tacoma neutral safety switch and how difficult is it to replace?
the neutral safety switch can be found by following the clutch pedal up into the bottom of the dash. its usually one or two 10mm bolts, and a connector. super simple to replace, it'll be the ONLY electronic piece connected to the clutch pedal
How do you take off engine fan?
Four bolts hold it on the clutch if it has one and 4 bolts hold it on front of water pump. Just remove them.
How do you take off engine cooling fan?
Four bolts hold it on the clutch if it has one and 4 bolts hold it on front of water pump. Just remove them.
How many bolts hold the starter on your 1988 B2000 pickup?
2 bolts hold it on
How do you remove the clutch on a 1991 prelude?
You will need to remove the transmission. Remove the clutch plate retaining bolts. Remove the clutch linkage. Remove the clutch retaining bolts.
How do you fit a new clutch to a vauxhall zaferia?
first undo all the nuts that hold the clutch housing, then remove it. next undo all the bolts holding the clutch in place, remove clutch and put new one in place, replace bolts & tighten them very tight. next screw on the clutch housing (the nuts don't need to be as tight). Easy really, piece of cake in fact
Can you reuse flywheel clutch torque bolts for Chevy 350?
i have replaced my clutch to 10.5 diemter ,can i re use the morso flywheel/clutch bolts
How do you replace the engine fan in Mazda mpv 2001?
First you have to remove the fan shroud which is bolted to the radiator and front cross bracket with 10mm bolts. There should be 4 10mm bolts that hold the fan and clutch to the water pump. What you generally have to do is find a way to hold the clutch fan in place, I have used a large flat tip screwdriver in the past. Then you have to loosen the 4 bolts and remove the clutch and fan as a single unit. Once out of the vehicle you should be able to remove the fan from the clutch unit and only replace the clutch unit itself. Hope that helps a little Michael
How do i replace Hydraulic clutch 1998 Chevy truck?
You will need to remove Transmission, And you will see it in the bellhouseing. 4 bolts hold it in place.
How many bolts in a Dodge Intrepid starter?
Three bolts hold it to the engine.
How many bolts hold the transmission to the engine on a 1995 K1500 Z71?
6 bolts hold the transmission to the back of the engine.
Clutch torque specs?
what is the torque for the bolts on the clutch springs for a trx 90/>
How many bolts hold in a Camry transmission?
Yes, bolts simply hold in a Camry transmission. That's just a law of nature
