0
What kind of bolts hold the ignition control module in a 1987 Ranger 2.3L?
Wiki User
∙ 9y ago
5.5mm bolts are the kind of bolts that hold the ignition control module in a 1987 Ranger 2.3L. However, 5.0mm bolts may also work.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
How to remove an ignition control module on a 1996 Nissan Altima?
The ignition control module is located within the distributor housing, so you need to remove the distributor, which is held in by two bolts, remember to slack off the valve cover bolts around the distributor, this facilitates the removal process, don't worry about the valve cover gasket it's an o-ring type gasket so it will reseal itself when you tighten the valve cover bolts .
Where is the ignition control module located in a 1995 cavalier and how do you wire it?
remove and install... ...everyone should have a manual for their vehicle, and the library should have a professional shop manual available for FREE to make copies of...read up and repair like a PRO! Dave :)
Where is ignition control module GM?
front of the engine above the starter,behind the coil packs (where all you spark plug wires are plugged into) remove all six 5.5 mm bolts from the ignition coils unplug two connectors on the left and one on the right.
Where is the ignition module on a 1993 Ford Taurus located?
On the bottom side of the engine( front of the car) just below the exhause manifold. It is easiest to remove the mounting plate from the body of the engine, as balancing the coils on the module as you remove and insert screws if a real pain in the but. If anyone has any suggestions on waterproofing this area, I would greatly appreciate it, as I have gone through three of these modules in three years due to water getting into it and shorting the module out. This last time it was a coolant leak around a seal on the top of the water pump, spraying right into the module that caused it. Argh!
How do you remove the control ignition module on a 1988 Chevy Celebrity 4-cylinder 2.5?
under neth the coil packs middle back of engine 3 bolts you will need a 10 milimiter 12 milimeter and 13 i did mine 4 TIMES !!!!
How do you change an ignition control module?
Remove 2 bolts. LOL mine is located on the throttle body
Where is the ignition control module for 1997 Chevy Cavalier 2.4L?
The ignition control module is located under the electronic ignition control module cover. On a 1997 2.4L cavalier, it will have the words 2.4L twin cam stamped on it. It is on the top of the engine and is held in place with four bolts. This cover must be removed to get to the spark plugs.
Where is the control module located on the 1991 Chevy Cavalier?
Not knowing what module, the ignition control module is behind the coil packs. 3 bolts hold all together against block, under the intake lower to mid center U
Where is the ignition module located on a 95 Pontiac Trans Am?
The Ignition Control Module (ICM) is located directly above the coil. If you remove the 2 bolts holding the coil on and then romove the coil mounting plate from the car you will see a small rectangular module with wires plugged into it. This is the ICM.
How to remove an ignition control module on a 1996 Nissan Altima?
The ignition control module is located within the distributor housing, so you need to remove the distributor, which is held in by two bolts, remember to slack off the valve cover bolts around the distributor, this facilitates the removal process, don't worry about the valve cover gasket it's an o-ring type gasket so it will reseal itself when you tighten the valve cover bolts .
How do you replace the ignition coil of an Alero?
Should be about 4-6 bolts holding the coils down to the ignition module, unscrew them bolts and then pull the coils up from ignition module, but disconnect your ground to your battery first and with precise placement, the plug wires as well
How do I locate the ignition module on a 1990 Chevy Celebrity?
The ICM is located on the passenger side, up under the dashboard. Remove the glove box and you can see it. It will be bolted to the side panel It is held on by 2 bolts, one on top, one on bottom. Disconect battery before removing! The above is the location of the engine control module or computer. If your car has the V6: The ignition control module is mounted to the lower part of the engine block on the radiator side of the engine. If you follow the spark plug wires down they will lead you to it. The coils are bolted to the ignition control module. If your car has the 4 cylinder engine: The ignition control module is below the intake manifold towards the rear of the engine. The spark plug wires will lead you directly to it. The coils are mounted on the ignition control module. It is in a awkward spot to get to.
Where is the ignition control module located on a 1992 Chevy Berretta?
ignition module is located under the distributor, where the spark plugs come out to go to the spark plugs, remove 6 bolts that hold the 3 capped distributor on, unplug the wires from both ends of module, 3 plugs, lift module out, nothing holds it in after distributor is removed, plug new module in, replace distributor.
Where are Mercedes vaneo spark plugs located?
At the front of the engine, behind a plastic cover, just above the exhaust manifold. There are 4 clips that hold the cover to the ignition module. Under the cover, there are 2 bolts that secure the ignition module to the engine. Disconnect the wiring plug on the end of the ignition module. Undo the bolts and use them to extract the module, then remove the plugs as normal.
How do you change an ignition module on a 1996 LSS?
Remove the 3 coils which are help on by 2 5.5 mm bolts each. The module is now free. Remove electrical connector from ignition module. - Tech JK -----------------------------------
Where is the ignition control module on a 93 Saturn sl2?
Look behind the red colored dipstick. You will see 2 ignition coils side by side (the spark plug wires connect to them) these are mounted on top of the ignition module. Each coil connects 2 spark plug wires. The coils have 2 bolts that hold them to the block. Disconnect the 2 plugs at the top of the ignition module. Remove the bolts holding the ignition coils to the ignition module and the whole assembly will come off.When replacing the coils, the spark plug order from left to right is 4-1-2-3 (the cylinder order on the block from left to right is 1-2-3-4).
Where is the ignition module for a 2000 alero?
The ignition module is right underneath the ignition coils. The ignition coils are what the spark plugs attach to. My alro was riding really rough so i just changed my coils and module for $200 and it runs like new. All you do is unplug the wires, unscrew the coils(6 bolts) and there is your module. :) Hope this helps!!
