0
What is the little box called that the positive and negative wires attach to coming from the battery of a 2003 Yamaha raptor 660?
Wiki User
∙ 16y ago
should be your starter selonoid...they are a common problem on raptors.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What is the procedure of the baterry?
The vehicle battery's main purpose is to supply power for the starting system and to power some accessories when the engine is not running. The proper procedure for changing or installing a battery... remove the battery cable first from the negative battery terminal, then from the positive. Install opposite, attach the positive cable lead, then the negative.
How do you jump start a 1998 Monte Carlo?
WARNINGFailure to follow these instructions carefully, especially in the + / - polarity matching of the hookups, could result in damage to both batteries and/or burns to your person. Please be safe.1 Open the hoods on both cars. Locate the batteries.2 Close the hood on the running car, and move it into position so that both cars' batteries are as close as possible. (Reopen the hood.)3 Attach a red jumper cable clamp to each battery's positive (+) terminal.4 Locate a large, unpainted metal surface on the engine of each car. A bracket near the alternator works best. (The alternator is a grapefruit-sized motor-like device on the front of the engine.)5 Attach a black jumper cable clamp to each location described in step 4.NOTE: The last connection you make could make a small spark, and the engine on the running car should slow slightly. If this does not happen, check all 4 clamp connections by wiggling them.6 Let the dead battery charge for about 5 minutes before attempting to start the car.More details belowTo jump a car, get some jumper cables and another car, and line the other car's front up with the dead one so that the batteries of each car can be as close enough together so the cables will reach. Leave the car with the good battery running. Now you're ready to connect the cables.Start by connecting the negative cable to each battery first. Then connect your positive cables. Be sure to "manage" your clamps so you don't short anything out. Triple check your battery polarities before making cable connections - do not blow it connecting the units up incorrectly. Negative to negative, and positive to positive.Have the one car that's fine running before making the last connection. What will happen when the last connection is made is that the "good" battery will start to charge the "dead" one, and this will drag down the "good" one. You'll want to have the vehicle with the "good" battery running so that the charging system can help transfer energy to the "dead" battery and minimize the impact of the discharge on your "good" battery. Wait a few minutes while the other battery charges off of the good one and the charging system of the operating vehicle.The car should start after that. If it sounded like it was going to start and it didn't, wait even longer and try again. Each time you try to start the car with the "dead" battery, you'll be draining the dead battery more, so make sure and let it charge a bit.Another answerJump starting a car battery is best accomplished with a pair of jump cables, normally sold in a "jump start pack", to jump start from the good battery of another car.It's a good idea to read your owner's manual on the subject. Certain manufacturers recommend different techniques. For example BMW suggests turning on the headlights and blower fan. The technique is to connect the positive cable from the jump pack between the positive terminal on your battery and the positive terminal on the other car's good battery, and the negative cable from the jump pack to the negative terminal on your battery, or - better - to a grounding point on your vehicle, to the other car battery's negative terminal.Don't ever get the jump cables reversed as doing that will cause the them to heat up so much that their insulation will melt and may even catch on fire and you may also cause damage to both cars' electrical systems.Make sure you know the voltage on your car, most are 12 volt systems but some are 6 volt. If jumping from another car make sure they are both the same voltage.Start the car to be jumped from and connect the positive cable ends to the positives terminals of both batteries and the negative cable to the negative terminals on both batteries. Allow the jumper car to run for a while before trying to start the jumpee car.Another way to start a car that has a dead batteryIf the vehicle with the dead battery has a manual transmission and it's parked on a hill, or you can push it to one, you can try another method: with the car in first gear and the ignition on, push in the clutch and let it roll down hill. When it gets going about 10 miles an hour or so, release the clutch quickly and it will snag the flywheel and force your engine to start turning, and that should start the car. If you aren't going fast enough, the engine will stall. Push in the clutch quickly after it starts and rev the engine a bit to insure it is going to keep running. Wait a few minutes before driving off to insure the battery gets a bit of a charge from the charging system, too. This can also be done in reverse, but it is much more dangerous, and it is inadvisable unless you are good at it and actually have a clear spot to roll backwards on.
How do i wire a 12 volt cigarette lighter plug on to a device like a c.b.radio?
On American cars the positive lead from your cigarette lighter is in the center of your socket. The adapter plug has the positive lead on the tip of the adapter and the negative lead on the side of the adapter. You need to use a volt-ohm meter to find out which wire comes from each lead. (You may be able to open the adapter and follow the wires that way).On the c.b. radio the positive lead should be red. This will connect to the positive lead on the adapter. The black lead on the c.b. radio is the negative lead. This will attach to the negative lead on the adapter.P.S. Usually the adapter will have a fuse built into it to protect from incorrect wiring.
Try to start car turn key in ignition and just goes click the engine not turning over or even trying to start?
there are two connections to the positive side of the battery, one to the starter, one to the accessories. some times corrosion get in between these two pieces. To correct this, i actual bought a battery with both positive connectors, (post and screw in) i hooked the starter up to one + part and the accessories to the other +. haven't had a problem since. Hope this helps
Diagram on how to replace the starter on a 1979 Chevrolet Impala?
Assuming a 350 engine, the starter is located on the passenger side of the engine, below the exhaust manifold. It is held in place with two bolts at the front, and one bolt securing a rear bracket. Disconnect both battery cables at the battery before beginning the job. The positive battery cable plus two more wires attach to the starter solenoid which is removed with the starter as one unit.
How do you change battery in 2004 gmc sierra?
1. Remove negative battery cable 2. remove positive battery cable 3. remove battery 4. install new battery 5.attach positive cable 6.attach negative cable
How do you charge car battery with solar charger?
Put the solar panel in the sun;Attach the red wire of the panel to the positive terminal of the battery;Attach the black wire of the panel to the negative terminal.
Why does your car battery spark when you attach the negative cable after you attached the positive first?
A small spark is normal, it is energizing the system.
How do you hook up jumper cables from one care to another?
To hook up jumper cables, attach one cable from the negative post on one battery to the negative post on the other battery. (These usually are marked "-" and have a blacl cable attached to them.) Attach the other jumper cable from the positive post on one battery to the positive post on the other battery. (These usually are marked "+" and have a red cable attached to them.)
What is the procedure of the baterry?
The vehicle battery's main purpose is to supply power for the starting system and to power some accessories when the engine is not running. The proper procedure for changing or installing a battery... remove the battery cable first from the negative battery terminal, then from the positive. Install opposite, attach the positive cable lead, then the negative.
How do you charge the battery on a Chevy hhr?
The battery is located in the cargo area. Access it by removing all of the shrouds as if you were getting to the spare. However there is a jumper/charger terminal under the hood. CAUTION: The fuse box outlet looks a lot like a negative terminal. IT'S NOT! DO NOT attach the negative [black] here. Attach the negative lead [black] to the metal of the engine. Then attach the positive [red] to the positive terminal near the front of the fusebox.
How do you replace a motorcycle battery?
Your battery is dead if it will not accept a charge. Begin by removing the battery cover. Next, remove the negative and positive cables. Lift the battery out of the motorcycle. Replace it with a new battery and attach the negative and positive cables. Turn on the motorcycle to check that the lights are working and start the motorcycle to make sure that it runs properly. Replace the battery cover.
Is positive on a car battery Red or black?
The red jumper cable attaches to the positive end of the battery. Make sure both cars are turned off before attempting to connect the cables and do not touch the metal portions of the cables together or to any part of the car except for the proper battery terminal.You'll first attach the positive (red) cable to the positive terminal of the dead battery. Then attach the other end of the red cable to the positive terminal of the working battery.Then attach the black cable to the negative terminal of the good battery, and finally attach the other end of the black cable to the negative terminal on the dead battery.Make sure everyone is clear of the engine and moving parts before starting the engine of the good car. Allow it to run for a couple of minutes, revving the engine slightly. Then start the engine of the dead car.Be sure to remove the cables in the reverse order of the way you put them on - negative first, then positive.
How do you jump start a Audi q7 battery?
Have someone park their car nose to nose o along side the Audi. With their car running, attach the red clamp to the positive terminal of the Audi battery and the corresponding red clamp to the positive terminal of their carâ??s battery. Then attach the black clamp to the negative terminals on both vehicles.
How do you jump the battery in a 2001 Chrysler sebring convertible?
Under the hood on the driver side are positive and negative jump start posts. The cables attach there.
How do you charge a motorcycle battery with a car battery?
You must get a couple of so-called jumper cables. The cables have strong clamps on them and are designed to be clamped to the battery terminals. Attach the black cable to the negative terminals of the motorcycle and car battery first. Then attach the red or positive cable to the positive terminals of the motorcycle and the car battery. In case your motorcycle battery is empty, you can now start the bike from the car battery. Disconnect the cables in reverse order, beginning with the red cable. The motorcycle battery will not be charged much by the car battery but the bike can be jump started by using this method.
How do you make a nine volt battery?
Arrange the four 1.5volts cells elongated in a line and connect the wires one from negative and the other from positive and to check attach it with a bulb or a toy car
