0
What else can I help you with?
How to replace starter on Ford Taurus sho?
Remove battery ground to avoid shorting Raise the front of vehicle so there is enough space to work underneath the front of the engine. Locate the starter from the underside of the car. It is near the transmission, underneath the exhaust manifold, between the engine block and the radiator. Locate the two bolts holding the starter to the engine at oposite positions 2 and 7 o'clock approximately, viewed from the left side of car. The upper bolt is actually a stud with two metric sized nuts a 13mm (deep dish socket required)and a 15mm. The lower bolt requires a metric size 13mm socket The bolts are threaded into the starter from the transmission side of the engine First remove the size 15mm nut on the upper bolt (2 o clock position) this will allow removal of the gound strap from the engine along with the wire harness support. Loosen the bottom bolt(metric size 13mm) but do not remove completely Using the deep size 13mm socket remove the upper bolt Next, remove the lower bolt.The starter should still be supported in its cradle at this stage but as a precaution support it by hand while you remove the lower bolt. Pry the starter loose from its mounting Lower it between the cross member and the engine - a little maneuvering is required When you have lowered it remove the lead(s) Replace in reverse order.
What size hex bolt on brake caliper on 2005 grand caravan?
For the front I believe a 15/16 socket will work. The rear I used a 7mm Allen wrench
Are t55 sockets the same as a m14 star bits?
T55 sockets refer to SAE sizes. (Standard Automotive Engineering). M14 is a metric size.
How do you determine the thread size of the gear shift knob on a 2001 Volkswagen Beetle GLS?
Take the knob with you to a hardware store, and find a metric bolt that will screw into the knob. This would be the easiest way.
What is the standard size of a furniture?
What is the standard size of a sofa?
What is the standard bolt size for a bike bottle cage?
The standard bolt size for a bike bottle cage is typically M5, which refers to a metric size of 5 millimeters in diameter.
What is the standard bottle cage bolt size for most bicycles?
The standard bottle cage bolt size for most bicycles is M5, which refers to a metric thread size of 5 millimeters in diameter.
What is the socket size for a 92 Geo Metro oil drain plug?
There is a good chance that it takes a standard size socket rather than a metric socket, it was like this on my Toyota Celica. 17mm
What size socket for cylinder head bolt Toyota 4runner 3.4?
It will be a metric size try different sizes until you find the one that fits.
What socket size is required for a three quarter inch bolt?
Bolts are categorised by their thread size. The standard socket size for a bolt with a three quarter inch thread is 1 and one eighth inches. Heavy head bolts use a one and a quarter inch socket.
What is the appropriate socket size for a 10.9 bolt?
The appropriate socket size for a 10.9 bolt is typically 17mm.
What standard socket fits a 27mm?
A 27mm socket is typically a standard size used for 1-inch drive socket wrenches. You would need a 1-inch drive socket to fit a 27mm bolt or nut.
What size of socket wrench used to remove bolt on air filter on 2006 hyundia elantra?
It will be a metric socket. Just try different sizes until you find the right one.
What is the size of bolt is used for the hood on a 1994 camaro?
There metric, get a metric set.
What are Bolt socket diameter?
The socket diameter of a bolt refers to the width of the opening in the head of the bolt for a socket or wrench to fit. It is typically determined by the size of the bolt and the type of socket needed for installation or removal. Common socket diameters for bolts range from 8mm to 24mm.
What size Allen socket is needed to remove caliper bolt on a 2004 Escape?
What size Allen socket is needed to remove bolt from caliper on 2004 ford escape
What is the standard size of a bike crank bolt?
The standard size of a bike crank bolt is typically 14mm.
