0
The PGM-FI unit is located under carpet at the passenger side. It covered by frame. Good luck. The ignition control module of any late model Honda/Acura product is always the PGMFI computer, which controls all fuel delivery and ignition timing coordination. Now, if you have a problem, that is ignition related, first replace the plugs, then the wires, and shortly after the ign coil itself. That's how you approach a Honda ign prob.
What else can I help you with?
What is the firing order for a 1988 Acura Legend?
The firing order for a 1988 Acura Legend is 1-4-2-5-3-6Additional info FYI: Ignition timing: 15 degrees BTDC #1 cylinder location: RIGHT-REAR
Does a 1988 Chevrolet G20 Van have points or an electronic ignition?
electronic ignition
How do you remove the control ignition module on a 1988 Chevy Celebrity 4-cylinder 2.5?
under neth the coil packs middle back of engine 3 bolts you will need a 10 milimiter 12 milimeter and 13 i did mine 4 TIMES !!!!
After 2 days of rain 98 Wrangler won't start nd it doesn't sound like its even cranking is this a spark or starter issue?
i had a similar problem myself on my 1988 jeep wrangler.i checked to see if i was getting a spark from the ignition coil and was not.after clount hours of changing various parts it came to me.the ignition module was the culprit.changed it and we were good to go
Where is the ignition module located on a 1989 Dodge d150 pickup truck?
The ignition module for this vehicle is mounted on the driver side fender well just below the hood hinge and behind a round vacuum diaphram.It is rectangle in shape and has a connector plug at one end(facing towards the front of the vehicle)and is mounted on a aluminum base with cooling fins(much like a small lawn mower engine)
Why 1988 Acura legend downshifts?
Why 1988 acura legend downshifts
What is the firing order for a 1988 Acura Legend?
The firing order for a 1988 Acura Legend is 1-4-2-5-3-6Additional info FYI: Ignition timing: 15 degrees BTDC #1 cylinder location: RIGHT-REAR
1988 Acura Legend bleed cooling system?
How do you bleed the cooling system of a 1988 acura legend? Is there a bleeding screw and where is it located?
Where is the ignition module located on a 1989 Mazda b2200?
where is the ignition module located on a 1988 Mazda b2200
How do you remove the ignition module on a 1988 ford f-250?
how do you remove the ignition control module on a 1988 ford f-250 pickup?
How do you change the ignition control module in a 1988 Chevy Silverado 5.7 L?
How do you change the ignition control module in a 1988 Chevy Silverado 5.7L
Is a 1990 Acura legend compatible with a 1988 Acura legend?
Some parts are, the 2.7liter is but some of it's electrical components are not
Where is the neutral safety switch located on a 1988 Acura Legend?
99 acura Ti
What is the transmission fluid capacity for a 1988 Acura Legend?
It is important to use the correct amount of fluid in a car. The 1988 Acura Legend takes about 3.2 quarts of transmission fluid.
What is the engine size of an 1988 Acura Legend?
2.7 litre.
What is the order of the ignition wires on a 6 cylinder 1988 Acura Legend?
1-4-2-5-3-6 the distributer turns counterclockwise hope i understood you right.
Where is the ignition switch module located on the 1988 Cherokee limited?
module locatedwhere is the module on a 9 Chevy blazer
