0
What else can I help you with?
How do you reset the change oil indicator on a 2008 Dodge?
First... Read your owners manual - page 226 - Turn the ingnition switch to ON (do not start) and fully depress the accelerator pedal slowly 3 times within 10 seconds and then turn the ignition switch to OFF .
How do you program the gm 15008009?
1. Close all doors2. Insert key into ignition3. Hold down the power UNLOCK button on the driver's door panel, continue to hold downuntil instructed to release in step 9.4. Perform steps 5 through 8 in a fairly rapid succession.5. Turn the ignition to the ON position (as far as you can go without starting the engine.)6. Turn the ignition to the OFF position.7. Turn the ignition to the ON position (as far as you can go without starting the engine.)8. Turn the ignition to the OFF position.9. Release the power UNLOCK button on the door panel. The vehicle should respond bydoor locks locking and unlocking automatically. (If locks do not cycle after you let go,not before you let go of the unlock button, then the vehicle has not entered programmingmode and you must start procedure over. Remove key from ignition, open drivers doorand return to step 1 ). If the locks do cycle automatically then proceed to step 10.10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock andunlock. This may take up to 30 seconds.11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).12. Turn the ignition to the ON position to exit the programming mode.13. Test remote(s).
Why is there an oil leak inside the ignition coil?
Ignition coils contain oil for cooling purposes. If your ignition coil has begun to leak it is only a matter of time before it fails. When it fails you won't be able to generate a spark to ignite the fuel in your engine. It would be best to replace your ignition coil now before it stops working.
What websites can you use for renting a vehicle before and after a cruise?
See the Link of the site in Related Links below. Renting a vehicle before and after a cruise.
If your insurance offers a discount for having an ignition immobilizer does a 1996 Monte Carlo Z34 require one or does it have a secure ignition lock?
96 Monte Carlos are equipped with GM PassKey 2 (the little chip you see in your key. Without that key, the car cannot be started. If someone tries to hot-wire the vehicle, not only will the computer not start the car but will also disable the starter and fuel injectors for thrre minutes before the car can be started again. To make a long answer short: Yes - this qualifies as an ignition immobilizer.
How do I authorize a key 2008 Ford Escape?
From the owner's manualProgramming spare keysYou can program your own coded keys to your vehicle. Please read andunderstand the entire procedure before you begin.Tips:• A maximum of eight keys can be coded to your vehicle.• Only use Securilock keys.• You must have two previously programmed coded keys (keys thatalready operate your vehicle's engine) and the new unprogrammedkey(s) readily accessible.• If no previously programmed coded keys are available, you must takeyour vehicle to your dealer to have the spare key(s) programmed.1. Insert a previously programmedcoded key into the ignition.2. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position.Keep the ignition in the 3 (ON) position for at least one second, but nomore than 10 seconds.3. Turn the ignition to the 1 (LOCK) position and remove the coded keyfrom the ignition.4. Within ten seconds, insert the second previously coded key into theignition.5. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position.Keep the ignition in the 3 (ON) position for at least one second, but nomore than 10 seconds.6. Turn the ignition to the 1 (LOCK) position and remove the secondpreviously programmed coded key from the ignition.7. Within twenty seconds of removing the previously programmed codedkey, insert the new unprogrammed key into the ignition.8. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position.Keep the ignition in the 3 (ON) position for at least one second but notmore than 10 seconds.
What is position 2 Mercedes -Benz IGNITION?
Position 2 on a Mercedes-Benz ignition switch typically refers to the "On" position, where electrical systems are activated but the engine is not running. In this position, functions such as the dashboard displays, radio, and other electronic components can be accessed. It is often used for pre-start checks and enabling accessories before starting the vehicle.
How do you program a key to a 2003 Ford Escape?
Programming spare keysYou can program your own coded keys to your vehicle. Please read andunderstand the entire procedure before you begin.Tips:• A maximum of eight keys can be coded to your vehicle.• Only use Securilock keys.• You must have two previously programmed coded keys (keys thatalready operate your vehicle's engine) and the new unprogrammedkey(s) readily accessible.• If no previously programmed coded keys are available, you must takeyour vehicle to your dealer to have the spare key(s) programmed.1. Insert a previously programmedcoded key into the ignition.2. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position.Keep the ignition in the 3 (ON) position for at least one second, but nomore than 10 seconds.3. Turn the ignition to the 1 (LOCK) position and remove the coded keyfrom the ignition.4. Within ten seconds, insert the second previously coded key into theignition.5. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position.Keep the ignition in the 3 (ON) position for at least one second, but nomore than 10 seconds.6. Turn the ignition to the 1 (LOCK) position and remove the secondpreviously programmed coded key from the ignition.7. Within twenty seconds of removing the previously programmed codedkey, insert the new unprogrammed key into the ignition.8. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position.Keep the ignition in the 3 (ON) position for at least one second but notmore than 10 seconds.
I ran out of gas. i then put gas in and it won't start.?
Try leaving your key in the "on" position for a few minutes. Your car has a pressurized system that needs to re-pressurize when it runs dry. The fuel pump only runs when the key is on the "on" position. ======================================================== When you turn your ignition key to the " RUN " position just before starting the vehicle , the ELECTRIC fuel pump will only run for 2 or 3 seconds if you don't start the vehicle . Try cycling the ignition key from the OFF position to the RUN position a few times if needed
I ran out of gas. i then put gas in and it won't start?
Try leaving your key in the "on" position for a few minutes. Your car has a pressurized system that needs to re-pressurize when it runs dry. The fuel pump only runs when the key is on the "on" position. ======================================================== When you turn your ignition key to the " RUN " position just before starting the vehicle , the ELECTRIC fuel pump will only run for 2 or 3 seconds if you don't start the vehicle . Try cycling the ignition key from the OFF position to the RUN position a few times if needed
I ran out of gas i then put gas in and it won't start?
Try leaving your key in the "on" position for a few minutes. Your car has a pressurized system that needs to re-pressurize when it runs dry. The fuel pump only runs when the key is on the "on" position. ======================================================== When you turn your ignition key to the " RUN " position just before starting the vehicle , the ELECTRIC fuel pump will only run for 2 or 3 seconds if you don't start the vehicle . Try cycling the ignition key from the OFF position to the RUN position a few times if needed
Have a aztek will turn off but the lights will not go off and the keys are locked in the ignition?
Check that you have the vehicle in the park gear position It has happened to me a couple of times before Good Luck Juan DC
How do you remove the power steering bracket without taking off to heads on a 2002 escape engine?
If your vehicle has a remote starter, you must turn the ignition switch to the "on" position before you depress the brake pedal.
How do you reset oil light for 2007 Chevrolet express?
Put the key in the ignition cylinder, turn to the run position or key on ignition off position (right before you crank the vehicle, for all the ignorant people). As soon as you do that press the gas pedal 5 times within 5 seconds. You will see the light flash, then your all good in da hood fool
Position your vehicle in the center of your lane before turning right and move toward the center line when you are about to turn left?
Use the position of your vehicle to communicate your intentions to change lanes. Position the vehicle in the right side of your lane before turning right and move toward the center line when you are about to turn left.
In a 2001 ford focus does the check engine light come on when it is started?
When the ignition key is turned to the run position just before starting the vehicle the check engine light should illuminate for a few seconds to prove that the bulb works
How do you check a check engine light on a 2001 ford ranger pu to see if it is burn out?
When you turn the ignition key to the run position just before starting the vehicle the check engine light will light for a few seconds to check the bulb
