0
It sounds like your 1991 Mazda RX-7 may have a problem with the idle air control or fuel delivery system, especially if it won't idle after the choke is off. Check the idle adjustment screw and ensure it's set correctly, as well as inspecting the throttle position sensor for proper operation. Since spraying ether doesn't raise the idle, it indicates that the engine isn't getting the necessary fuel, so also check the fuel pump, fuel filter, and injectors for any blockages or issues. If you can access a repair manual online, it may provide you with specific adjustment procedures and troubleshooting steps.
What else can I help you with?
What is the adjustment of valve tappet clearance of Mitsubishi 4dr5 diesel engine?
.24mm intake and exhaust [cold engine] ref: misubishi Jeep service Manual 4dr5
What temperature should your vehicle be when adjusting the intake and exhaust valve?
cold Look up the specs in a shop manual, it will indicate if the adjustment is done H (hot) or C (cold).
What is the valve adjustment specs for 2006 350 Honda rancher?
The valve adjustment specs for a 2006 Honda Rancher 350 typically require the intake valves to be set at 0.005 inches (0.127 mm) and the exhaust valves at 0.007 inches (0.178 mm). It's essential to perform this adjustment when the engine is cold for accurate measurements. Always refer to the owner's manual or a service manual for detailed procedures and specifications.
What is the valve adjustment gap for a 22hp kawasaki engine?
The valve adjustment gap for a 22hp Kawasaki engine typically ranges from 0.005 to 0.007 inches (0.127 to 0.178 mm) for both intake and exhaust valves. However, it's essential to consult the specific engine model's service manual for the exact specifications, as they can vary. Proper adjustment ensures optimal engine performance and longevity.
What is the difference between electric and manual choke on carburetors?
electric chokes work on heat and electrical power to do the adjustment, manual chokes YOU are the adjuster as you drive u move a choke knob for the adjustment.
What is the valve clearance adjustment for a 2003 Honda rancher 350es 4x4?
The valve clearance adjustment for a 2003 Honda Rancher 350ES 4x4 is typically set to 0.004 inches (0.1 mm) for both the intake and exhaust valves when the engine is cold. It’s crucial to use a feeler gauge for proper measurement during the adjustment process. Always refer to the owner's manual or service manual for specific procedures and torque specifications. Regular checks and adjustments help maintain optimal engine performance.
What is the sequence of valve lash adjustment and specs for both intake and exhaust for a 1991 Ford Escort GT?
Purchase a Haynes or Chilton's repair manual at any auto parts store. Here you will find all the valve and torque specs.
How do you adjust Linkage for 89 Chevy Cheyenne manual transmission?
no adjustment on the 5speed manual transmission with overdrive. hydraulic clutch
Sentence for manual?
We were told to read the manual before we entered the classroom.They did a manual search of the files.The car had a manual transmission.Manuel, what page in the repair manual will tell me how I will make a manual adjustment to the manual transmission?
How do you adjust the transmission linkage on a 93 mercury topaz manual transmission?
The 1993 Mercury manual transmission linkage will have adjustment nuts on each end of the linkage. Turning the adjustment nuts will move the linkage back in forth.
What are the valve adjustment specs on a 2006 trx350tm?
The valve adjustment specifications for a 2006 Honda TRX350TM typically require an intake valve clearance of 0.004 to 0.005 inches (0.10 to 0.13 mm) and an exhaust valve clearance of 0.005 to 0.006 inches (0.13 to 0.15 mm). It's important to check and adjust the clearances when the engine is cold for accurate measurements. Always refer to the owner's manual or service manual for specific procedures and detailed information.
What is wrong if my Manual transmission will not go into reverse?
Coud be linkage adjustment Or something internal
