0
First, make sure you have the correct remote.
FCC: E4EG8D-444H-A.
Also, do you have memory seats in your MDX? If so, make sure your remote says MEM 1 or MEM 2 on back.
For programming:
Do steps 1 - 12 on the same remote (AT TIME OF PROGRAMMING BOTH REMOTES MUST BE PRESENT SINCE THEY WILL NOW BOTH HAVE TO BE REPROGRAMMED.) The following steps 1-12 are done on a single remote step 10 is done on all remotes to be programmed up to 4 can be programmed
1) get into the car shut the doors (including trunk or tailgate) and make sure they are unlocked
2) turn on the ignition (number II position)(do not turn on the engine just the ignition til the dash lights come on) (LISTEN FOR A QUIET CLICK)
3) press the lock button on remote (turn to off) (Do not remove key)
4) quickly turn on the ignition (do not turn on the car just the ignition) (LISTEN FOR A QUIET CLICK)
5) press the lock button on remote (turn to off )
6) quickly turn on the ignition (do not turn on the car just the ignition) (LISTEN FOR A QUIET CLICK)
7) press the lock button on remote (turn to off )
8) quickly turn on the ignition (do not turn on the car just the ignition) (LISTEN FOR A QUIET CLICK)
9) press the lock button on the remote
the locks should cycle to indicate that programming mode was entered successfully
10) press the LOCK button on each remote you want programmed and the door locks should cycle again to confirm programming. THIS STEP NEEDS TO BE DONE FOR EACH REMOTE
11) turn off the car fully and remove key.
12) try locking/unlocking with remote to test
The important thing is to quickly turn the ignition off then on after hearing the click and pressing the lock button. If you hear the click in the off position, you waited too long and must start over.
This does work, I just used it to program my 2004 MDX, 10 minutes ago. Although it took a couple tries.
What else can I help you with?
How do you program keyless entry remote for 1989 Buick Park Avenue?
The 1989 Buick Park Avenue does not come with a remote keyless entry. The keyless remote entry was not available till 1997.
How do you program a keyless entry remote for a 1997 z28 camaro?
check in your owners manual if you have it.
How do you program a 1997 Chrysler stratus keyless entry remote?
The dealership scan tool is required.
How do you program keyless remote for a 1997 dodge ram 1500?
To program your keyless remote, locate the dark green program enable wire and connect to the wire enable terminal. Insert your ignition key and turn the switch to on while depressing either button on the transmitter. Disconnect the program enable wire terminal and remove the key from the ignition.
Did all 1997 thunderbirds come wih keyless remotes?
Mine didn't come with a keyless remote.
Did the 1997 Dodge Grand Caravan come with a keyless remote?
It was optional.
How do you program keyless entry remote for 1997 buick lesabre?
Follow this link and you're good to go. Let me know if you have any questions. I've done this myself so I know how to do it. .ehow.com/how_7291758_program -remote-1997-buick-lesabre.html#ixzz1HA YkCKDX
How do you program keyless remote on a 1997 Cadillac Catera?
To program a keyless remote for a 1997 Cadillac Catera, first, sit in the driver's seat and close all doors. Insert the key into the ignition and turn it to the "On" position without starting the engine. Press and hold the "Lock" and "Unlock" buttons on the remote simultaneously for about 15 seconds until the doors lock and unlock, indicating successful programming. Repeat this process for additional remotes, and then turn the ignition off to exit programming mode.
How do you program a keyless entry remote 1997 buick park avenue?
To program the keyless entry remote you hold down the lock and unlock keys at the same time while within 10ft of vehicle to make sure you are within range of the remote for approx 10 seconds. the vehicle will alert with a short horn sound. if it does not respond, repeat. should only take 1-3 tries before it's done
How do you program 1997 Infinity Q45 Keyless Remote?
To program a 1997 Infiniti Q45 keyless remote, first, sit in the driver's seat and close all doors. Insert the key into the ignition and turn it to the "On" position (not starting the engine) and then back to "Off" eight times within 10 seconds. After the eighth turn, the doors should lock and unlock, indicating the car is in programming mode. Press any button on the remote to program it, and the doors will lock and unlock again to confirm successful programming. Repeat the button press for any additional remotes.
How do you program the keyless remote on a 1997 jaguar xk8 to sound the horn when pressing the to lock button?
To program the keyless remote on a 1997 Jaguar XK8 to sound the horn when pressing the lock button, first, ensure the vehicle is in the "Run" position without starting the engine. Then, press and hold the "Lock" and "Unlock" buttons on the remote simultaneously for about 10 seconds until you hear a confirmation sound. This will enable the horn feature when locking the vehicle. If needed, consult the owner's manual for specific instructions or troubleshooting tips.
How do you program a remote keyless entry for a 1996 Cutlass Supreme SL?
Try: http://www.programyourremote.com/ It has instructions for 1997-2000 models, perhaps they'll work with the 1996 model. Good luck!
