0
What else can I help you with?
How do you remove the inner cv hub from the transaxle?
Before you remove CV axle from tranny, be prepared to catch tranny fluid. Use a pry bar to separate it from tranny. When installing new part, place a piece of wood on end of outer CV joint before striking with hammer (with it installed in steering knuckle).
How do you remove you joint on Toyota pick up?
To remove the joint on a Toyota pickup, first, safely lift and secure the vehicle. Then, disconnect the battery and remove the wheel for better access. Use a socket or wrench to detach the bolts securing the joint, and if applicable, gently tap with a hammer to loosen it. Finally, carefully pull the joint from its housing, ensuring to check for any additional retaining clips or components that may need to be removed.
How to pull the transmission in 1997 Honda civic?
You remove the axle nuts and a ball joint to remove the CV axles. Then you remove the shifter linkage. Remove the starter and all the other stuff that's hooked to the tranny. Then you place a jack under the engine. Remove all the bolts holding the tranny and the engine together. Now unhook a couple motor mounts, raise the car up, drop the engine down and slide the tranny out. You do not have to remove the motor to take the engine out. You simply need to take all the bolts out of the tranny that are going into the motor and then remove it from the motor with the motor in the car.
How do you remove a CV joint on a 1997 Toyota Tacoma?
To remove a CV joint on a 1997 Toyota Tacoma, first, safely lift and support the vehicle, then remove the front wheel. Next, disconnect the axle from the hub by removing the axle nut and any bolts holding the hub assembly. Once the axle is free from the hub, use a pry bar to push the CV joint out of the transmission or differential, taking care not to damage any surrounding components. Finally, reverse the process to install the new CV joint.
How do you remove the ball joint from the tie rod end on a 86 Toyota 4x4?
The ball joint should be permanently in the tie rod end. If it is bad, you have to replace the entire tie rod end.
1994 Toyota Camry cv joint picture?
i need the picture of a 1994 Toyota Camry xle cv joint diagram
How do you remove the wiper arms on a 1999 Toyota sienna after removing cap and nut?
bang the joint (where the arm pivots) with your palm. this will free it from the tapered shaft.
How do you replace a CV joint on a 1993 Mercury Capri XR2?
replace the axel!!! not just the joint. you have to remove the ball joint and the tie rod end. just remove the nut off the bottom of the tie rod end and it shouldn't mess up your alinement. then you have to remove the nut that is under your rim so you must remove your tire. and take that nut off also. and replace the wheel baring also if your going to replace stuff anyway.I think auto zone had a lone a tool program or something to remove the axel from the tranny. it just pops out. its easyer then it looks.
How do you remove a transmission from a Isuzu truck?
1. Get the truck up on ramps and jack stands.. Make sure it's not going anywhere cause neither the e-brake or gears will help you. 2. Disconnect battery. 3. Disconnect the 4wd universal joint and main universal joint. (you will need to move the ebrake cable out of the way so go back into the cab and take the ebrake off. 4. remove the cross member 5. Loosen and remove all the bolts and nuts holding the tranny housing to the engine. 6. Top passenger side will be your last NUT and it's a tuffy. It and the main shaft will hold the tranny up. 7. Position a tranny jack underneath and slide the tranny out. This is rather simplified but it should get you started just fine.
What is the high whining noise from the passenger side of a 94' dodge caravan?
If you only hear it when it is moving, it is the tranny or a bearing. if it does not change pitch when the tranny shifts, it is a wheel bearing or cv joint. if it rumbles when you turn sharp left or right, it is a cv joint.
How do you replace a ball joint?
Remove the tire and wheel. Remove the brake assembly and rotor. Remove the retaining nut from the ball joint. Pound the ball joint out with a hammer. Reverse the process to install the new ball joint.
How much of General Motors stock does Toyota own?
18 % in a joint venture g.m. and Toyota in 1983 g.m. gave Toyota a plant that g.m. had not used in 25 years toy Toyota .in return Toyota gave g.m. a % of stock.
