0
First you need to get the right tools for the job and the right parts to fix the problem. There is a hinge pin in both the upper and lower hinges and four brass bushings and there is two different size bushings in each hinge and also two hinge pin retaining washers. As for the tools, you need a spring compressor, jack, hammer, punch. First, open the door all the way and put jack under door. I like to use a 2-by-4 board on top of the jack to help spread the weight of the door out a little. Next, if the door has a wiring harness in the jamb loosen the rubber insulation form both the door and the body. This gives a couple of inches of slack in the wiring. Next use the spring compressor to remove the spring, then use the punch and hammer to drive out the pins. It is very hard to get them to move at first but gets easier as they start to move. I would recommend having a helper to hold the door upright as it will fall when the pin is removed from the hinge. Once the pins are out move the door and jack away from the body, to gain more access room the replace the bushings: two in the door side and two in the body side. Then slide door and jack back and align hinge holes and install new pins. I always grease the bushing and pins before installing. Drive the new pins all the way flush with the hinge and install the retainers. Reinstall the spring and reattach the wiring insulation.
What else can I help you with?
How do you replace a 96 thunderbird driver side door bottom hinge pin?
You have to replace the whole hinge assembly, they don't make a hinge pin kit for the Thunderbird.
Replace door hinge 1989 Mitsubishi Triton?
need to replace door hinge pin on 189 mitsibushi Triton tray back
What is the name for pin that slides into a door hinge?
The pin that slides into a door hinge is called a hinge pin. It is usually removable to allow for door removal or adjustment.
How do you replace a door hinge pin in a 1997 grand marquis?
To replace the door hinge pins on a 1997 Jimmy you will need to open the door up. Place two jack stands on the front and back of the door's length at the bottom portion of the door for support. Remove the damaged hinge pin with the proper socket. Place the new hinge pin in place and secure it.
How do you replace a hinge pin on a 1993 dodge spirit?
To replace the hinge pin on a 1993 Dodge Spirit, first, remove the door from the vehicle by supporting it and unbolting the hinges. Once the door is off, use a hammer and a punch to drive out the old hinge pin. Insert the new hinge pin into the hinge, ensuring it is properly aligned, and then reattach the door to the vehicle, securing the hinges with bolts. Finally, check the door's alignment and make any necessary adjustments.
How do you replace door hinge pin and bushing on Crown Victoria?
The pin will probably have to have the bottom end that is flared out cut off or drilled out. The pin can then be tapped out. This is easier if the hinge has been removed but then the door will have to be blocked up into place while the hinge is off.
How do you replace front door pin on a 1999 cadillac deville?
Buy a new or find a used door hinge . Forget about replacing the pin
How do you replace door hinge pins on a 1993 Mercury Cougar?
Hold the end of the door with a jack, grind the head from the old pin, knock out the old pin, remove the door half of the hinge, drill out the hinge to accept the new bushings, install the new bushings, re-bolt the hinge to the door, finally, insert the new pin and install the C clip
How do you replace a hinge pin on a 1987 Chevy blazer?
break off the bottom bushing that hold door pin pick up on the door slightly use a hammer and screw driver to drive pin out and replace
1986 GMC Vandura rear door hinge pin is broken?
If the rear door hinge pin on your 1986 GMC Vandura is broken, you will need to replace it to restore proper door function. Start by removing the door from the hinges, then carefully extract the broken pin. You can purchase a replacement hinge pin at an auto parts store or online. Finally, reinstall the door with the new pin, ensuring it's aligned correctly for smooth operation.
How do you replace door hinge pin bushings on a 1999 GMC sierra?
I have a 1999 gmc 1500 sierra,need to replace door pins and bushings.door sagging.
What is a door hinge pin?
A hinge pin is a pin that holds together two hinge plates, one of which is fastened to the door and the other is fastened to the door jamb. There are usually two or three hinge assemblies used on each door, one near the top, one near the bottom, and sometimes one at the middle.
