0
You'll have to remove the inner carpet inside the hatch behind the taillight, there is 2 nuts to remove before being able to pull out the whole housing, don't drop the nuts into the body of the car. There is a plug to remove that conencts to the lights housing before you pull it out. Then remove the housing, unclip the back of the light and on that pannels should be 2 lights. Remove the one you need and replace it.
What else can I help you with?
What tool to replace brake light bulb in 2007 Chevy truck?
3rd brake light or rear brake lights?
How do you replace brake light on 2007 Ford 500?
From inside the trunk.
How do you replace 2007 Toyota Avalon 3rd brake light?
To replace the third brake light on a 2007 Toyota Avalon, first, open the trunk and locate the plastic cover that conceals the brake light assembly. Remove the cover by unscrewing or unclipping it, then disconnect the electrical connector from the old light assembly. Next, remove the old brake light by unscrewing or pulling it out, and install the new light by reversing the process. Finally, reconnect the electrical connector and replace the plastic cover.
How do you replace the third brake light in your 2007 Toyota Avalon?
The third brake light on a 2007 Toyota Avalon is replaced by first removing the rear, retaining screws. The wiring harness can then be disconnect and the light bulb removed.
How do you replace the high mount brake light on a 2007 Chevy Cobalt?
To replace the high mount brake light on a 2007 Chevy Cobalt, first, open the trunk and locate the plastic cover at the rear of the vehicle. Remove the cover by unscrewing or unclipping it, then gently pull it away to access the brake light housing. Disconnect the old bulb by twisting it counterclockwise and replace it with a new bulb, ensuring it is securely in place. Finally, reattach the cover and test the brake light to ensure it functions properly.
How do you replace a rear trunk brake light on a 2007 Mercedes CLK 350?
To replace the rear trunk brake light on a 2007 Mercedes CLK 350, first, open the trunk and locate the light assembly. Remove the trim panel or cover if necessary, then twist the light socket counterclockwise to release it from the assembly. Pull out the old bulb and replace it with a new one, ensuring it's securely in place. Finally, reassemble the light socket and trim panel, and test the brake light to confirm it's functioning properly.
How do you replace a brake light bulb on a 2007 Cadillac CTS?
The brake light bulb on a 2007 Cadillac CTS can be replaced by opening the truck, removing the rear cover, and disconnecting the wiring harness. The bulb can then be twisted, removed, and a new bulb put in its place.
Where are the brake light fuses on a Nissan navara 2007?
You can find the 2007 Nissan brake light fuse in the fuse box. The brake light fuse will be in the second column, third from the top.
How do you Replace brake light on 2007 jeep commander?
To replace the brake light on a 2007 Jeep Commander, first, open the rear hatch and locate the tail light assembly. Remove the screws or clips securing the tail light, then gently pull it away from the vehicle. Disconnect the wiring harness and remove the old bulb by turning it counterclockwise. Finally, insert the new bulb, reconnect the wiring, and reattach the tail light assembly.
How do you change the brake light switch in a 2007 Chevy Colorado it has two switches?
how to change brake light switch in a 2007 chevy colorado
How do you reset brake light on 2007 BMW x5 4.8i?
To reset the brake light on a 2007 BMW X5 4.8i, first ensure the brake light bulbs are functioning properly and replace any burned-out bulbs. Then, turn the ignition to the "On" position without starting the engine. Press the gas pedal three times within a few seconds to reset the brake light warning. If the light persists, you may need a diagnostic scan to check for any underlying issues.
How do you change the high mount brake lite on a 2007 Taurus?
The way that you change a high mount brake light on a 2007 Taurus is by first prying the light assembly from the housing. You then push rearward to remove it from the retaining clips. Next, life the light assembly from the shelf and disconnect the assembly wiring. Replace the light assembly and reverse directions to put the light housing back where it goes.
