answersLogoWhite

0

The small ones have 153 teeth, the large ones are 168.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How many teeth on a Chevy 305 flywheel?

Depends. There were 168 and 153 teeth. Both were used on 305's.


How many teeth are on a 350 Chevrolet starter?

A 350 Chevrolet starter typically has 9 teeth on its pinion gear. This design is common for many small block Chevy engines to ensure proper engagement with the flywheel. However, it's always a good idea to verify the specific starter and flywheel combination for your engine, as variations can exist.


How many teeth on ring gear of 4g54 engine?

The Mitsubishi 4G54 engine uses a flywheel with a ring gear that has 131 teeth. This ring gear is essential for the starter motor to engage and crank the engine during starting.


How do you know how many teeth are on a 350 Chevy flywheel?

There are two common flywheels or flexplates for the 350's. The one that is just under 13" diameter is 153 teeth. The one that is just over 14" is 168.


How many types of starters are there for a 1983 305 Chevy engine?

Depends on what the 305 is in, a 305 camaro engine needs like a 9 tooth starter because the fly wheel is 12.75 inches in diameter with 50 some teeth. A 305 in a Chevy half ton will have like a ten tooth starter for the 14.25 inch diameter flywheel that has like 60 some teeth. All 305 engines before 1986 are the same they did have different flywheels for what ever Chevy put them in. 1986 and newer 305's had different cranks the flywheel bolts up different on a 1986 305 compared to a 1983 305.


How many teeth on a flywheel of a 4G54?

The 4G54 engine, commonly found in Mitsubishi vehicles, typically has a flywheel with 132 teeth. This number may vary slightly depending on the specific model and year, so it's always best to consult the vehicle's service manual for precise specifications.


How many teeth have 1985 ford bronco II flywheel?

The flywheel for a 1985 Ford Bronco II typically has 153 teeth. This is common for many Ford small-block engines of that era, which the Bronco II would likely be equipped with. Always check specific vehicle specifications or service manuals for confirmation, as variations may exist based on the engine type or model modifications.


How many labor hours for a flywheel on a 96 Chevy truck?

It will take and experience mechanic six hours to replace your 1996 Chevy truck flywheel. A novice mechanic will take several more hours.


How many bolts is a 91 Mitsubishi Eclipse Gs non turbo motor flywheel?

The flywheel for the FWD tranny should have 6 bolts. The turbo flywheel has 100 teeth and the nonturbo should have 106. The AWD flywheel should have 7 bolts.


1984 ford Bronco2 new flywheel and starter will engage one time then spin What causes this?

Assumeing it's the same starter, the bendix(the gear on the end of the starter that engages the flywheel)could be bad, and or the starter it self could be bad. sounds like number of teeth on new flywheel does not match number of teeth on starter. find out from mechanic that installed new fly wheel, how many teeth on flywheel if he doesnt know, a ford dealer can tell you from the part number on your receit. then ask how many teeth should be on starter to match fly wheel pull starter and count teeth


How many teeth do flies have?

No No. Flies vomit on their food to dissolve it then suck it up with a straw like extension. A flywheel has teeth.


How many freeze plugs are there between the engine block and flywheel on a dodge 3.9 liter v6 engine?

Two.