answersLogoWhite

0

When the engine is cold it should be up to the cold fill mark

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

What should the raidiator coolant level be?

The coolant level is set by the level in the coolant reservoir. There is a line for the level if the engine is cold and a line for if the engine is up to temperature. You should fill it to the corresponding line.


How much coolant should be put in the reservoir for a 2003 s600?

Fill it up to the full mark.


How do you filling coolant?

Add coolant to the full cold line on the coolant reservoir when engine is cold.


How much coolant to fill a 1997 Saturn sw1?

The amount of coolant it will take to fill your vehicle is dependent upon how low the coolant level is. You can add coolant to your coolant reservoir. The reservoir will have an indicator of when the coolant system is full.


Where is the radiator reservoir on the Toyota Echo 2000?

Look to the right of the radiator cap, which is at the top of the radiator. You can't miss it. It has a "low" and a "full" line on it and your coolant level should always be between those lines.


How do you know when to top up coolant?

Most vehicles have a full line or add line marked on the coolant reservoir. Open reservoir only when vehicle is cold.


How much coolant should be in the reservoir of a 1990 dodge spirit when the engine is cold?

About 2/3 full.About 2/3 full.


Where do you check coolant on a 800 intruder?

To check the coolant on a Suzuki 800 Intruder, locate the coolant reservoir, typically positioned near the right side of the bike, near the engine. Ensure the engine is cool, then inspect the coolant level through the transparent reservoir; it should be between the "low" and "full" marks. If the level is low, add the appropriate type of coolant as specified in the owner's manual. Always check for any signs of leaks or damage in the cooling system.


How do you Fix a no heat problem in 2004 Sebring?

Sometimes its just low coolant, check reservoir and add to full mark heat should come on


How do you check the coolant level on a Honda Rancher 350?

To check the coolant level on a Honda Rancher 350, first ensure the engine is cool. Locate the coolant reservoir, typically found near the radiator, and inspect the level against the markings on the side of the reservoir. The coolant should be between the "low" and "full" marks. If necessary, add the appropriate type of coolant to reach the correct level.


Do you add coolant to the reservoir or the radiator?

If there is a cap on the radiator you can check to see if the radiator is full , and if it isn't , " top up " the engine coolant . Otherwise , you check the engine coolant level at the engine coolant reservoir when the engine is cold and maintain the level at the cold mark


How do you put in antifreeze in a 1992 Toyota Previa after flushing out the system?

Open the hood and the Coolant reservoir on the '92 Previa is next to oil reservoir on the left side. Unscrew radiator cap from the coolant reservoir, add the 50/50 mix of coolant fluid into the reservoir. (Recommend use Prestone extended life coolant) Fill the coolant into the reservoir, it take about 3 gallon, and be sure that the coolant is pass the full mark of the reservoir. Now, turn on the car, during the engine running (about 10 minutes) kept check the level of coolant be sure it still maintains pass the full mark level. Screw back the radiator cap to coolant reservoir. Run engine for another 30 minute. This will ensure that thermostat is open and and ensure the fluid is circular all around of the radiator and hoses. Waite engine cool down, then open the radiator cap and check the coolant fluid level. If the level is low then add more coolant. Do not fill the coolant pass the full Mark's point. If the coolant fluid is still the same as in full mark then it is good. Continue to check the coolant fluid for next couple day. Besure that it is at the full level mark.