0
What else can I help you with?
How do you change a strut mount on a Mitsubishi montero?
The bottom strut mount is connected to the frame by two retaining bolts. Remove the retaining bolts to remove the strut mount. Reverse the process to install the new strut mount.
How do you replace a strut mount on 2007 Buick lucerne?
To replace the strut mount on a 2007 Buick Lucerne, first, safely lift the vehicle and remove the front wheel corresponding to the strut you are replacing. Then, detach the strut assembly by loosening the upper strut nuts under the hood and the lower bolts at the steering knuckle. Replace the old strut mount with the new one, reassemble the strut assembly, and ensure all nuts and bolts are securely tightened before reinstalling the wheel and lowering the vehicle. Always consult a repair manual for specific torque specifications and safety precautions.
How many engine mounts does a 95 Cavalier have?
There is one on the front passenger side and a torque strut on the front. The torque strut acts like a motor mount.
How do you Adj strut for wheel alignment on 2004 impala?
To adjust the strut for wheel alignment on a 2004 Chevrolet Impala, first, ensure the vehicle is on a level surface and lift it using a jack. Loosen the strut-to-knuckle bolts and the strut mount bolts, then use an alignment tool or a leveling device to adjust the strut position. After achieving the desired alignment specifications, tighten the bolts to the manufacturer's recommended torque specifications. Finally, recheck the alignment to confirm that it meets the required angles.
What is the purpose of a torque strut mount?
Basically, the purpose of the torque strut mount is to keep the engine and transmission from vibrating excessievely. This smooths the ride, keeps the engine/transmission from excessivel stressing the engine/rtansmission mounts on the frame, and provides for a smoother ride and better drivability. Without the torque strut mount, the top of the engine would be unsupported and damage to the drive train would occur.
What part hold the left rear strut to the body on the 94 Geo metro?
The left rear strut on a 1994 Geo Metro is held to the body by a combination of bolts and a mounting plate. Specifically, the top of the strut is secured to the body through a strut mount that typically consists of three bolts. The bottom of the strut connects to the rear control arm with another bolt. Proper torque specifications should be followed during installation for safety and performance.
What is the front strut torque spec for a 2010 Subaru Legacy?
The front strut torque specifications for a 2010 Subaru Legacy typically require that the upper strut mount nuts be torqued to about 14 ft-lbs (19 Nm) and the lower strut bolts to around 80 ft-lbs (108 Nm). It's crucial to consult the vehicle's service manual for precise specifications and any additional details specific to your model. Always use a calibrated torque wrench for accurate measurements.
How do you change an alternator in 85 fiero-V6?
The torque strut mount must come out along with the mount to remove the alternator
How do you change toqure strut on 2007 ford 500?
To change the torque strut on a 2007 Ford 500, start by safely lifting the vehicle and securing it on jack stands. Remove the lower engine mount bolt and any necessary components blocking access to the strut. Then, unbolt the torque strut from the engine and the subframe, replace it with the new strut, and reassemble everything in reverse order. Finally, ensure all bolts are tightened to the manufacturer's specifications before lowering the vehicle.
How do you change front struts on a 1988 Pontiac Grand Prix?
You can replace the strut cartridges without removing the entire assembly. Simply jack up the front of the vehicle, and rest it securely on jack stands. Remove the top cover plates covering the strut towers (held on by three nuts). Once the plate cover is off, remove the upper strut nut, and remove the rubber mount. You'll need a special die-tool to remove the strut cartridges.. Remove the old ones, install the new. Torque them to the proper spec. Re-install the mount, the upper nut, and the plate cover. Torque all nuts to the proper specs.... ENJOY!!! You can replace the strut cartridges without removing the entire assembly. Simply jack up the front of the vehicle, and rest it securely on jack stands. Remove the top cover plates covering the strut towers (held on by three nuts). Once the plate cover is off, remove the upper strut nut, and remove the rubber mount. You'll need a special die-tool to remove the strut cartridges.. Remove the old ones, install the new. Torque them to the proper spec. Re-install the mount, the upper nut, and the plate cover. Torque all nuts to the proper specs.... ENJOY!!!
How to replace motor mounts in 1995 dodge neon?
You've got 4 mounts total. A transmission mount, then on the other side of the motor, you've got a mount that goes to the middle of the engine that is in the fender, and upper torque strut and a lower torque strut on that same side.
How do you replace torque strut mount on a 1999 Chevrolet Cavalier?
Some people call it the "Dogbone" mount. Because that is what it resembles. It is located underneath the engine on the passenger side. It prevents the engine from spinning around when you give it gas and go.Simply remove the 2 bolts (15mm i belive) that mount it,knock it out with a hammer or pry it out with a screw driver(your choice), put in the new mount,put the two bolts back in and go...simple.
