0
To set the gap on a Poulan chainsaw's magneto, you typically want to adjust it to around 0.020 inches (or 0.5 mm) using a feeler gauge. This ensures proper ignition and engine performance. To adjust, loosen the mounting screws, place the feeler gauge between the magneto and the flywheel, then re-tighten the screws once the gap is set. Always refer to your specific chainsaw model's manual for the exact specifications.
What else can I help you with?
What is the point gap on a poulan 306 chainsaw?
Should be set at 0.015" to 0.016" gap
What is the spark plug gap on a poulan 2150 chain saw?
The spark plug gap for a Poulan 2150 chainsaw is typically set at 0.025 inches (0.635 mm). It's important to ensure that the gap is correctly set for optimal engine performance and efficient ignition. Always refer to the owner's manual for specific recommendations, as variations may exist based on the model or modifications.
What should the T screw on a poulan chainsaw carburetor be set at?
The T screw on a Poulan chainsaw carburetor, which typically adjusts the idle speed, should generally be set at around 1 to 1.5 turns out from the fully seated position. However, optimal settings can vary based on the specific model and external conditions, so it's advisable to consult the owner's manual for precise adjustments. Always fine-tune the settings while the chainsaw is running to ensure proper idle performance.
Troubleshoot No firing from armature magneto and spark plug?
air gap improperly set between fly wheel and magneto, bad coil, spark plug harness. Would not hurt to check the spark plug gap and ensure the connector end is tight
How do you adjust idle on poulan wild thing chainsaw?
Use the idle speed adjustment screw to set the idle speed as low as possible without stalling. http://store.chainsawr.com/
How do you adjust idle on Poulan Wild Thing 2375 Chainsaw?
Use the idle speed adjustment screw to set the idle speed as low as possible without stalling. http://store.chainsawr.com/
What is the magneto gap for a Yamaha banshee?
The magneto gap for a Yamaha Banshee, specifically the 350 model, is typically set at 0.012 to 0.014 inches (or about 0.3 to 0.35 mm). This gap is crucial for ensuring proper ignition timing and optimal engine performance. It's important to check and adjust this gap during maintenance to ensure reliable operation. Always refer to the specific service manual for your Banshee for the most accurate specifications.
What is the ignition coil gap for a Stihl 024 chainsaw?
The ignition coil gap for a Stihl 024 chainsaw is typically set to around 0.2 mm (0.008 inches). This gap ensures proper spark generation for efficient engine performance. It's important to use a feeler gauge to accurately measure the gap when adjusting. Always refer to the owner's manual for specific guidance on your model.
What is the ignition coil gap for a stihl ms250 chainsaw?
The ignition coil gap for a Stihl MS250 chainsaw is typically set to approximately 0.2 mm (0.008 inches). This gap ensures proper spark generation for efficient engine performance. It's important to check the gap periodically and adjust it if necessary during maintenance. Always refer to the owner's manual for specific recommendations and guidelines.
What causes engine on craftsman riding mower to backfire?
valve sticking, up, bad spark pulg, bent or worn keyway,More...It could also be that the idle speed is set too high, causing the cylinder to "load" excessively when you turn off the key. Also might check the magneto gap -- the gap between the rotating magnetic head and the prongs on the magneto coil. (I usually use a matchbook cover or a business card to set this.)
How can you tell if the magneto in a riding lawn mower is bad?
does it have spark to the plug if not the part you might check would be the coil or the electronic start module probably the latter if it is a newer mower or of ots older then the coil magneto usually dont go bad could be a bad gap between the coil and the magneto if its an older mower could be a bad set of points if its an older mower point gap could be bad spark plug could be bad as I don't know exactly what the lawn mower is doing hard to tell what is wrong
What is the point gap on Yamaha DT250?
The point gap on a Yamaha DT250 typically refers to the gap between the ignition points in the magneto system, which should be set to approximately 0. points when the points are fully open. This gap is crucial for proper ignition timing and engine performance. Always refer to the specific service manual for your bike’s model year for the exact specifications.
