0
Why would a 2000 Blazer have no brake lights if the bulbs and fuses have been replaced?
Possibly the brake light switch. not sure where it is located tho. maybe under the dash attached to the brake pedal lever. it may have a spring loaded button on it so that as soon as you push the brake lever the least bit the button comes out allowing the switch inside to connect. this switch malfunction usually causes the brake lights to stay ON tho.hope this is the problem.
Have you considered the relay? I believe the brake lights are engaged via relay on the 2000 Blazer. Check your hazard lights and your third brake light.
I am the previous anonymous. I have done some research and discovered that your vehicle has actually been recalled because of this very problem! Check the NHTSA's website or contact your local Chevrolet service center to set up an appointment for free service on the recalled part (actually a multifunction switch which also relates to your hazard lamps). The recall Campaign ID is 01V364000. The Part Number is 506377. .
check your hazard switch. despite what most dealerships say, you can replace just the hazard/4-way switch which is much, much cheaper than the entire turn signal assembly they try to sell you. that fixed my brake light problem
----------
brake lights are wired through the turn signal switch. the switch is needed to interrupt power to the brake light that needs to blink for turn signal useage., also to allow the lights to blink when flashers are used.
turn signal switch failure is usually the cause of no brake lights. replace the switch assembly. if the third brake light always works then it is the turn sig switch assembly that is causing the issue with the brake lights not working.
What else can I help you with?
No brake lights on s-10 blazer?
It is important to have working brake lights on a vehicle. If the brake lights are not working a person should first check the fuse, bulbs and at last the wiring.
You changed bulbs and fuses and still your brake lights do not work on your 91 S-10 Chevy Blazer?
Check the brake light switch.
Where can you find a diagram of brake system for 1986 Chevy pickup?
i have tail lights but do not have brake lights nor do i have turn signals. i have replaced brake switch and all bulbs
Your brake lights will not work on a 1994 ford escort you have already replaced bulbs and fuses?
Working brake lights are important for safety reasons while driving. It is important to check all of the wiring, if the brake lights are not working and the fuses and bulbs have been checked.
Fix non working brake lights on 2000 s10 blazer?
Check the fuse, check the bulbs and check the brake light switch, in that order.
How do you fix brake lights on 1995 Chevy blazer?
Check the fuse, check the bulbs and check the brake light switch, it should be one of those.
You have replaced the bulbs and the brake switch still no bottom brake lights on a 95 Chevy lumina?
Check sockets and grounds
Why wont all of the brake lights come on on a 745il.bulbs have been replaced?
use BMW bulbs and parts
1995 Chevy blazer and all your lights work except brake lights but the third brake light works?
I assume you have checked/replaced the bulbs. Take a cicuit tester and check the wire harness connections under the bumper and around the trailer connector if you have one. The problem must be at that area IF all your other lights are working as you said.
Why are the brake lights not working when the blinker and regular lights are working on a 98 cadillac el dorado All fuses and bulbs have been replaced?
How about a malfunctioning brake light switch
When the brake lights come on why do the side lights come on in a Ford Fiesta mark 4?
mines dun this it was wen a replaced the rear brake lights it was dogy bulbs put new wans in n it was sorted
My tail lights and third brake light work on my 98 Explorer the two main brake lights do not Already replaced the brake light switch and all fuses appear to be intact What next?
I hate to ask , but did you check the bulbs ? The tail light portion may work fine , but the brake lights don't if both of the bulbs are bad .
