0
Yes, a 302 intake manifold can fit a 360 block, but it depends on the specific engine configurations and the intended application. The 302 and 360 engines are both part of the Ford small-block family, but they have different port sizes and bolt patterns. Modifications may be necessary for proper fitment and performance, so it's essential to check compatibility before installation.
What else can I help you with?
Will A 302 Intake Manifold Fit on A 360?
No, a 302 intake manifold will not fit on a 360 engine, as they are designed for different engine configurations. The 302 is a small-block engine, while the 360 is a larger small-block with different dimensions and bolt patterns. To use a 302 intake on a 360, you would need an adapter, but it's generally not recommended due to potential performance issues. It's best to use an intake manifold specifically designed for the 360 engine for optimal performance.
Intake manifold torque specs 1973 Ford f100 360?
what is the torque setting 1973 FORD F100 360 engine . for my heads and manfuld thanks
Will a dodge 1968 318 intake manifold bolt up to 1976 360 motor?
all small block mopar part interchange......... 68 manifolds have smaller ports. 76 has emission ports in them.you need 75-78 manifolds
Where is the oil sensor located on a 360 Dodge?
Rear of engine block, behind intake, next to distributor
Will a 2001 318 cu in engine work in a 1995 Ram 1500 truck or will you have to change Manifolds?
Should be o.k. as long as it is a 318 truck. 360 is balanced different.Check the rear of intake manifold for an egr valve,some models,years do or do not have an egr valve.simple manifold swap will fix this.exhaust should be fine.watch out for grand Cherokee 318, it has starter on other side of the block!
What is the firing order for a 1972 Plymouth satellite 318?
The firing order for the small block Chrysler engines of this era is 1 8 4 3 6 5 7 2. Engines of v-8 design under 360 cubic inch displacement (5.9 litre) are small block design. Most factory intake manifolds have the firing order cast into the manifold
What is the firing order for a 1971 AMC 360 V8 engine?
1-8-4-3-6-5-7-2 If it stilll has the stock intake manifold it's written on it.
Where is the temp sending unit located on a 1992 ram van 250 360 ci?
On a 1992 Ram Van 250 with a 360 ci engine, the temperature sending unit is typically located on the engine block near the thermostat housing. It's usually found on the driver's side, threaded into the intake manifold or the cylinder head. To access it, you may need to remove any obstructions, such as air intake components or wiring harnesses. Always ensure the engine is cool before attempting to locate or replace the sending unit.
Where is the water temp sensor on a 1987 Dodge 360 engine?
On a 1987 Dodge 360 engine, the water temperature sensor is typically located on the intake manifold, near the thermostat housing. It is usually threaded into the manifold and connected to the wiring harness that relays temperature information to the gauge on the dashboard. Always ensure to consult a repair manual for precise location and specifications for your specific vehicle model.
Will a 1990 Dodge 360 tbi unit and intake bolt to a 1987 318?
no heads and intake are different form a 360 to a 318
How much horsepower does it have?
it comes with a 302 ,360 ,411 ,365 horsepower engine
Will a Dodge 1991 318 v8 tbi unit and intake manifold fit and work properly on a 1974 Dodge 318 or 360 v8?
As far as bolting up, yep, it's a go. Not certain how many, if any, sensors would need to be added to the block and/or heads. Also, the distributor will need to be the one from the TBI engine, since it functions as a cam position sensor for the injection/computer. A friend put a 1990 TBI 360 into a 1985 Chrysler Fifth Avenue after swapping the injection for a 4 barrel intake and carb, so I know it bolts up.
