answersLogoWhite

0

What else can I help you with?

Related Questions

How do you reset the security light on a suburban?

You can do it with a scanner. Usually when the security light is flashing it means there is a problem with the passlock system. Dealer item and about $500.00-$700.00 to replace parts & reprogram.


How do you reset passlock on 2001 Saturn?

Turn the engine two seconds then leave the key in the run position for exactly ten minutes...the anti-theft security light should go from blinking to solid at the ten minute mark. Immediatly run the engine and the Passlock is reset. Good Luck!!


How do you reset 1999 Chevy Venture passlock?

the 1999 venture has the PK3 system for security, so you have to go to a GM dealer or a automotive locksmith that has the proper box to reset it or make a new master key for it.


Is there a security to reset on a 2001 Chrysler PT Cruiser after the cam sensor and the crank sensor have been changed?

Chrysler does not use reset switches.Chrysler does not use reset switches.


How do you reset passlock on 2004 alero?

Turn the key to "on" and let it sit for approx 10 minutes until the 'security' light stops flashing. Turn to off and start as normal.


Can you reset passkey II on a GM truck?

Passkey II can be reset based on the type of Truck you are looking at. You can usually reset it by the steps below. To determine if the passkey is your problem you need to know if the security light is flashing, solid, or out. Observe the Security indicator lamp in the instrument panel. Remove the key from the lock cylinder. - Security indicator should be Flashing when the door is open. - Security indicator should be Off when all the doors are closed. - If the Security indicator does not come On or go Off correctly, refer to the Content Theft Deterrent System diagnostic and repair information in the applicable Service Manual. With the Doors closed, place the key in the lock cylinder and turn to the Run position. Observe the Security indicator lamp. - Lamp is On and does not go Off however, the engine starts. This indicates that the Vehicle Theft Deterrent (Passlock) system detected a fault when the engine was running. - Lamp flashes On and Off. This indicates a problem has been detected by the Passlock(Passlock™) system and the engine may not start this key cycle, a current condition. If you determine that the Passlock is the issue, you need to do some web research on the "corrosion of the passlock system" GM had massive issueswith them and you may be able to get the answer there.


How do you reset a dashboard security light 2002 GMC Sierra 1500?

To reset the fashing dash blue security light............disconnect the hot lead on the battery and after about 3 minutes, reconnect it. Light should be off now.


How do you reset the security light in your 2001 Oldsmobile Alero?

== == The repair below is a theft password relearn procedure. It may get your car to start for a while, but does not repair the problem. The most common cause for this problem is the PASSLOCK ignition cylinder. It may need to be replace, then re-learned again.- TechJK -------------------------------------- Turn the key to the on position for about 30mins. After the first 10 minutes the security light starts to blink. Then it turns solid again after another 10 minutes. The last 10 minutes is to reset the passlock system (you can leave it on for longer to make sure you reset it). Now take the key out and try to start the car. I had to do this when my car was not starting; the fuel pump was off because of my passlock system.


The car will not start and the horn honks and lights flash; how do you reset?

wait 10 minutes for the passlock system to reset for a GM vehicle.


How to reset the passlock on 1998 Chevy 1500?

cut the yellow small wire from ign. switch in the column up by the switch. this is the passlock wire. but will it start iwas told that it wouldnt


Why does your 2000 impala not crank after your security light comes on?

passlock has been activated you have to turn the key to the on position for 10 minutes for the computer to reset but it may take up to thirty minutes or longer to crank sometimes.


How to reset passlock on an s10?

30 Minute Learn Procedure1. Turn ON the ignition, with the engine OFF.2. Attempt to start the engine, then release the key to ON, vehicle will not start.3. Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.4. Turn OFF the ignition, and wait 5 seconds.5. Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes, the vehicle is now ready to relearn the Passlock™ Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.ImportantThe vehicle learns the Passlock™ Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.6. Start the engine, the vehicle has now learned the Passlock™ Sensor Data Code and/or password.