answersLogoWhite

0

In an Inline 6 Jeep engine, the idler pulley is located to the right of the A/C pulley. It is a smooth pulley, not a grooved one.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

What does idler pulley look like on 2004 Jeep liberty?

It is one of those small round items that the belt rides on. The idler is not attached to an accessory such as the power steering or alternator.


Where is the idler pulley on a 1990 Jeep Wrangler 4 cylinder and what does it look like?

It's located on the front of the engine. It's belt pully that isn't "driving" anything. It's just chillin' spinning freely..


How do you change the serpentine belt idler pulley ona 2006 Isuzu ascender?

Requires two person team. Step One: Look at serpentine belt diagram on front of engine. Arrow points to idler tension pulley. (Front Left side of engine) Loosen this 15mm bolt. Step Two: Loosen Idler pulley bolt - 15mm. Step Three: One person push down on idler tension pulley with tire removal tool or cheater bar on front left of engine while second person lifts belt off alternator. Step Four: Remove Idler pulley and replace with new one. Tighten bolt to idler pulley Step Five: One person push down on idler tension pulley with while the other fits belt on alternator and around idler pulley. Step Six: Make sure belt fits as noted on belt diagram and Tighten bolt on idler tension pulley (front left side of engine). Approximate time: 10 minutes


Where is the tensioner pulley on a 2005 sable?

Open the hood. Now look at all the pulleys. The one that is not connected to any component and is not driving anything, is the idler tensioner pulley.


Where is the idler pulley located on a 1994 GMC Sierra?

i dont really know-but to find out just look it up on google!


How do you Adjust serpentine belt on 1992 Cherokee 4.0?

I believe there is an idler pulley which keeps the belt tight on the 4.0. If you are experiencing slop or looseness, I suggest you look at replacing the belt or maybe the idler is stuck or broken. I had to replace an idler in a Wrangler once.


How do you replace idler pulley 1996 ranger 3.0?

The bolt on the idler pull loosens the normal direction, lefty loosey on the ford ranger 3.0 engine. If you look lower, you'll notice the tension pulley. You can tell it's the tension pulley by the pivoter arm that it's bolted to. Take the proper size wrench or socket, and turn clockwise as if you were to tighten it. It takes a little bit of force, but the whole arm assembly should turn down taking tension off the belt. You can then slide the serpentine off of the idler pulley and remove the pulley.


How do you put on a new power steering belt on a 1997 Jeep Grand Cherokee?

Is this a single belt or a serpentine belt system, if so look for belt tension idler pulley and loose belt, or single belt then you will need to loose and release tension on the power steering pump assembly.


Where is the starter motor on a 99 jeep?

Look at the lower rear of the engine


When should you change serpentine belt on vw 2001 passat?

Check the serpentine belt for cracking and "checking" by a close visual examination. Look at the "inside" of the belt where it rides on the pulleys. The grooves should not be cracked, or missing ridges on the inside of the belt. Also, check the idler/tensioner pulley bearing for noise/wear. I changed mine when I replaced the spur ( timing ) drive belt and tensioner/idler pulley/shock absorber at 100,000mi. I also replaced the AC compressor drive belt and idler/tensioner pulley at that time.


What does a Ford Explorer water pump look like?

the water pump will be on the very front of the motor and have a big pulley bolted to it and a cooling fan bolted to the pulley


How do you stop an alternator belt from squealing on a 1993 Plymouth Laser 20 L non-turbo when you have already replaced the alternator and belt several times and checked the tension on the belt?

Try tightening the mounting bolt on the idler and/or tensioning pullies. This did the trick for a persistent squeek on my 93' Jeep Wrangler. On some cars, the idler pulley {usually on the belt tensioner) can squeal. If you squirt some WD-40 or similar lubricant on the front of the bearing (engine off), and the noise goes away, it is probably the bearings in the idler pulley. If this is the case, replace the idler pulley, because the noise will come back after the lubricant gets slung out of the bearing. I also have a Plymouth laser, I had the same problem and tryed the same things. If the above answers don't seem to work, look at the water pump. In the water pump there are ball bearings the keep it spinning smoothly and when the casing of the bearings give way, the bearings no longer glide over the surface, instead they bunch up and rub against the back of the pulley. If this is the case, you will be able to see the bearings behind the pulley.