0
The ignition cylinder on a 2002 Hyundai is a quick repair. First the lower steering column will need to be removed so the lock cylinder can be accessed. Once off, loosen the mounting screws for the cylinder. Insert the key and push the tab in while turn the key slightly so the cylinder can be unlocked from the housing.
What else can I help you with?
How do you remove ignition lock key without key?
Removing a ignition lock cylinder from a 2002 ford windstar with no key
Does a 2002 Hyundai accent have a distributor cap?
No, the 2002 Hyundai Accent does not have a distributor cap. It uses a distributor-less ignition system (DIS), which eliminates the need for a traditional distributor and cap. Instead, it relies on individual ignition coils for each cylinder to deliver spark directly.
How do you remove front struts on a 2002 Hyundai sonata?
how do you remove the rear struts/shocks on 2002 hyundai sonata.
How do you change the ignition switch on a 2002 Hyundia Accent?
To changeÊthe ignition switch on a Hyundai Accent, first, one should remove the switch from the steering column, to which it is attached. From there, the component can be replaced.
How do you change an ignition switch in a 2002 Hyundai Elantra?
1. Disconnect negative battery cable 2. Remove the steering column covers and lower instrument panel cover 3. To remove the electrical portion of the ignition switch follow the harness back and disconnect the electrical connector then remove the screw and detach the switch from lock cylinder housing 4. Lower the steering column 5. The switch/lock cylinder housing is clamped to steering column by shearhead bolts. Use a chisel and hammer to tap the bolts in a counterclockwise direction to unscrew them 6. Remove the lock cylinder/ignition switch assembly from the steering column
How do you change ignition lock on 2002 Pontiac aztek?
To change the ignition lock on a 2002 Pontiac Aztek, start by disconnecting the negative battery cable for safety. Remove the steering column covers and then access the ignition switch by unscrewing it from the column. Use a key to turn the ignition to the "Accessory" position, which will allow you to press the release tab and remove the old lock cylinder. Finally, insert the new ignition lock cylinder, reassemble the steering column covers, and reconnect the battery.
How do you replace ignition cylinder 2002 Pontiac aztek?
To replace the ignition cylinder on a 2002 Pontiac Aztek, first, disconnect the negative battery terminal to ensure safety. Then, remove the steering column cover by unscrewing the screws and gently prying it apart. Insert the key into the ignition and turn it to the "Run" position, allowing you to press the release pin on the ignition cylinder. Finally, pull out the old ignition cylinder and insert the new one, ensuring it locks into place before reassembling the steering column cover.
How do you remove the back seat in a 2002 Hyundai accent?
To remove the 2002 Hyundai accent rear seats find the tabs that cover the bolts and unbolt them. After the bolts are out lift the seat to remove it from the car.
Is the 2002 Hyundai sonata 4-cylinder 2.4L an interference engine?
Yes , the 2.4 liter 4 cylinder in a 2002 Hyundai Sonata is an interference engine ( according to the Gates website - they make timing belts etc . )
How do you replace the ignition cylinder switch on a 2002 sunfire?
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder
2002 impala ignition key hard to turn why?
it is either the key is worn out or the key cylinder in the ignition is worn out.
How do you replace ignition switch in 2002 Bravada?
To replace the ignition switch in a 2002 Bravada, first disconnect the negative battery terminal to avoid electrical shorts. Remove the steering column covers by unscrewing them, and then detach the ignition lock cylinder if necessary. Disconnect the wiring harness from the old ignition switch and remove it by unscrewing the mounting screws. Install the new ignition switch by reversing these steps, ensuring all connections are secure before reattaching the battery.
