0
What else can I help you with?
How do you remove a dodge Dakota 2007 seat belt reminder?
1. With all doors closed and the ignition switch in anyposition except On or Start, buckle the driver's seat belt.2. Turn the ignition switch to the ON position and waitfor the Seat Belt Warning Light to turn off.3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driver'sseat belt at least three times within 10 seconds, endingwith the seat belt buckled.NOTE: Watch for the Seat Belt Warning Light to turn onwhile unbuckling and off while re-buckling the seat belt.It may be necessary to retract the seat belt.4. Turn the ignition switch to the LOCK position. Asingle chime will sound to signify that you have successfullycompleted the programming.1. With all doors closed and the ignition switch in anyposition except On or Start, buckle the driver's seat belt.2. Turn the ignition switch to the ON position and waitfor the Seat Belt Warning Light to turn off.3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driver'sseat belt at least three times within 10 seconds, endingwith the seat belt buckled.NOTE: Watch for the Seat Belt Warning Light to turn onwhile unbuckling and off while re-buckling the seat belt.It may be necessary to retract the seat belt.4. Turn the ignition switch to the LOCK position. Asingle chime will sound to signify that you have successfullycompleted the programming.
How do you disarm the seat belt alarm in a 2008 dodge Dakota?
1. With all doors closed and the ignition switch in any position except On or Start, buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming.
How do you reset timing belt light on Toyota revo?
To reset the timing belt light on a Toyota Revo, turn the ignition key to the "ON" position without starting the engine. Press the gas pedal three times within five seconds, then turn the ignition off. When you start the engine again, the timing belt light should be reset. If the light remains on, it may indicate the need for a timing belt replacement or another issue.
When replacing a timing belt on a 93 mercury villager do you need to use a timing light?
not for changing the belt. however you will need it for the ignition timing once you have replaced the timing belt
How do i disable the seatbelt chime on my 2010 town and country?
1. Sit in the drivers seat with the key in the off position. 2. Buckle the seat belt. 3. Turn the ignition key to the "on" position without starting the engine. and Wait for the seat belt light to go off. 4. Within 1 minute, unbuckle and re-buckle the seat belt 3 times, ending with the belt buckled. Each time you buckle the belt, wait for the belt light to go off. 5. Turn off the ignition key. A chime will sound indicating the change has been accepted. Repeat the procedure to turn the seat belt chime back on.
How do you fix no seat belt warning light or sound warning on 2003 Hyundai Santa fe?
Plug The Seat belt in.
How do you turn off the seat belt bell for a 2004 jeep liberty?
The following steps must occur within first 60 seconds of ignition switch being turned to ON or START position. 1) Turn ignition switch to OFF position, and buckle the driver's seat belt. 2) Turn ignition key to theACCESSORY/RUN position, and wait for the Seat Belt Warning Light to turn off. 3) Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4) Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming. The seat belt light will remain lit when belt is not fastened, but chime will not go off. To reactivate chime, repeat procedure 1-4 above.
Ford Taurus marble sound under load?
A marble sound under load indicates the engine is out of time. Have the ignition timing checked and the timing chain/belt for damage or excessive play.
How do you disable seat belt chime in a 2005 dodge magnum?
The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the LOCK position and buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat BeltWarning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure.
How do you reset1998 Toyota hiace van timing belt light?
To reset the timing belt light on a 1998 Toyota Hiace van, first, turn the ignition switch to the "ON" position without starting the engine. Then, locate the trip meter reset button on the dashboard. Press and hold the button while turning the ignition off and then back to the "ON" position. Continue holding the button until the timing belt light goes off, indicating that it has been reset.
What is belt loop?
A belt loop is a highway which loops around the perimeter of a major city, or a loop of fabric ringing the waist of a pair of trousers, used to hold the belt in place.
What is a belt loop?
A belt loop is a highway which loops around the perimeter of a major city, or a loop of fabric ringing the waist of a pair of trousers, used to hold the belt in place.
