answersLogoWhite

0

To enable constant velocity.

It keeps a shaft turning through a range of angles.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How to replace steering column universal joint in Hi ace lh-51?

To replace the steering column universal joint in a Hiace LH-51, first ensure the vehicle is securely lifted and supported. Disconnect the battery and remove the steering wheel and column covers to access the universal joint. Unbolt the old joint from both the steering column and the steering shaft, then install the new joint by securing it in place with the bolts. Finally, reassemble the steering column, reconnect the battery, and test the steering for proper function before lowering the vehicle.


Does the speed increase in a universal joint?

No, a universal joint does not increase speed. Its primary function is to allow flexibility in the drivetrain to transmit power between shafts that are not in a straight line.


What does the universal joint on the propeller shaft of an automobile function?

The universal joint is used to transfer drive (power) from one shaft to another when they are inclined (non collinear) to each other.


How do I replace the universal joint in my 2002 Kia Sportage AWD?

To replace the universal joint in your 2002 Kia Sportage AWD, start by safely lifting the vehicle and removing the driveshaft. Use a socket and ratchet to remove the bolts securing the universal joint to the driveshaft and the differential. Carefully press or hammer out the old joint, then install the new universal joint by aligning it properly and securing it with the bolts. Finally, reattach the driveshaft, ensuring all bolts are tightened to the manufacturer's specifications before lowering the vehicle.


What is the function of an u joint in a car?

The u-joint (universal joint) allows the driveshaft to transfer power from the transmission to the differential during constantly changing angles.


Allwheel drive mitsubuhi Montero clunk noise when you accelerate?

You most likely have a bad universal joint. This universal joint is located in the drive line of the vehicle and needs replaced as soon as possible.


How do you change universal joint 87 Chrysler fifth ave?

To change the universal joint on a 1987 Chrysler Fifth Avenue, first raise the vehicle securely and support it on jack stands. Remove the driveshaft by unbolting it at the rear differential and the transmission. Carefully pry out the old universal joint, then install the new one by inserting it into the yoke and securing it with clips. Reassemble the driveshaft and ensure all bolts are torqued to the manufacturer's specifications before lowering the vehicle.


How do you replace a 2004 Honda CR-V rear universal joint?

To replace the rear universal joint on a 2004 Honda CR-V, first, safely lift and support the vehicle, then remove the rear driveshaft by unbolting it from the differential and the transfer case. Next, mark the position of the driveshaft for reassembly, and use a press or a hammer to remove the old universal joint from the driveshaft. Install the new universal joint by ensuring it is properly seated, then reassemble the driveshaft, aligning it with your previous marks, and securely bolt it back in place. Finally, lower the vehicle and check for any unusual noises during a test drive.


How do you change a universal joint on a 1999 suburban?

To change a universal joint on a 1999 Suburban, first lift the vehicle and secure it on jack stands. Remove the driveshaft by unbolting the u-joint straps or clips at both ends, then carefully slide the driveshaft out. Using a u-joint press or a hammer, remove the old u-joint from the driveshaft and replace it with the new one, ensuring to grease it if required. Reassemble the driveshaft, securing it with the straps or clips, and lower the vehicle once everything is tightened.


What do you put universal joints in?

a universal joint holder.


How do you change universal joint on the steering columm?

To change the universal joint on the steering column, first, ensure the vehicle is securely positioned and disconnect the battery. Remove the steering wheel and any necessary covers to access the column. Unbolt the universal joint from the steering shaft and the connecting part on the steering gear. Replace it with the new joint, ensuring proper alignment, and reassemble the steering column components before reconnecting the battery and testing.


Who invented the universal joint?

The first universal joint was created by Londoner Robert Hooke, a scientist of the 17th century.