answersLogoWhite

0

because they cannot be differentiated from inclusions

of stored material without a special stain .

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Biology

What if You did not apply heat during the application of the primary stain?

Without heat, the primary stain may not penetrate the cell wall properly, leading to poor staining results. Heat helps to enhance the penetration of the stain into the bacterial cells, improving the visibility of the stain under the microscope. Thus, not applying heat during the application of the primary stain may result in weaker staining and difficulty in observing the bacterial cells.


What equipment should be used when making slides of cheek cells to observe under a microscope?

To make slides of cheek cells for microscopy, you will need a microscope slide, cover slip, swab or toothpick to collect the cells, a staining solution (such as iodine), and a microscope with at least 400x magnification. You may also need a pipette or dropper to apply the staining solution.


What is the importance of heat fixing the slide before staining?

You heat fix a slide by passing it through a blue flame a couple of times (with th cells facing up). you do this to denature any enzymes that might lyse the cells or interfere with the staining procedure. you also use it kill the organism and to adhere the organism to the slide for staining


Assume that during the performance of this exercise you made several errors in your spore staining procedure?

Assume that during the performance of this exercise you made several errors in your spore-staining procedure. In each of the following cases indicate how your microscopic observations would differ from those observed when the slides were prepared correctly . A. you used acid-alcohol as the decolorizing agent . B. you used safranin as the primary stain and malachite green as the counterstain C. you did not apply heat during the application of the primary stain · A. Normally tap water is used as the decolorizing agent to wash off excess stain. When you use acid-alcohol, it decolorizes the cells and the stain is removed. · B.When you use safranin as the primary stain and malachite green as the secondary stain, the cells will stain green and the spores will stain red. · C.When heat is not applied during the application of the primary stain, the spores are not stained and they appear colorless.


How do you determine the location of starch in a leaf?

Starch can be located in a leaf by using a staining technique such as iodine staining. Iodine reacts with starch to produce a blue-black color, making it visible under a microscope or to the naked eye in a plant sample. This method helps to identify the presence and distribution of starch in different parts of the leaf.

Related Questions

How long after staining can you apply polyurethane to wood surfaces?

You can typically apply polyurethane to wood surfaces 24-48 hours after staining.


Do I need to apply wood conditioner before staining?

Yes, it is recommended to apply wood conditioner before staining to help the wood absorb the stain more evenly and prevent blotchiness.


Do you need to apply wood conditioner before staining?

Yes, it is recommended to apply wood conditioner before staining to help the wood absorb the stain more evenly and prevent blotchiness.


How do you apply wood conditioner before staining?

To apply wood conditioner before staining, first sand the wood surface. Then, use a brush or cloth to evenly apply the wood conditioner in the direction of the wood grain. Allow the conditioner to penetrate the wood for the recommended time before wiping off any excess. Finally, proceed with staining the wood as usual.


How long after pre-stain can I apply the stain to my project?

You can typically apply stain to your project 24 hours after pre-staining.


Do you apply waterproofing product before or after staining the deck?

It is generally recommended to apply waterproofing product after staining the deck. Stain helps to enhance the appearance of the wood and the waterproofing product helps to protect the wood from moisture and prolong its life.


How can I effectively prevent staining on MDF board during the finishing process?

To prevent staining on MDF board during the finishing process, you can apply a coat of wood sealer or primer before painting or staining. This will help to seal the surface and prevent the MDF from absorbing the finish unevenly. Additionally, make sure to sand the MDF board thoroughly and clean it well before applying any finish to ensure a smooth and even application.


How can I achieve a consistent finish when staining wood filler?

To achieve a consistent finish when staining wood filler, make sure to apply a pre-stain wood conditioner before staining to help the wood filler absorb the stain evenly. Additionally, sand the wood filler smooth before staining and apply the stain in thin, even coats, allowing each coat to dry completely before applying the next one.


Can you mix processing lotion with henna and apply it to relaxed hair?

Yes, but you run the risk of permanently staining it unless your hair is perfectly relaxed. Try using some scented candles during the proccess.


What if You did not apply heat during the application of the primary stain?

Without heat, the primary stain may not penetrate the cell wall properly, leading to poor staining results. Heat helps to enhance the penetration of the stain into the bacterial cells, improving the visibility of the stain under the microscope. Thus, not applying heat during the application of the primary stain may result in weaker staining and difficulty in observing the bacterial cells.


How can I effectively prepare wood for staining by using pre-staining techniques?

To effectively prepare wood for staining using pre-staining techniques, start by sanding the wood to create a smooth surface. Next, apply a wood conditioner to help the stain absorb evenly. Finally, use a pre-stain wood sealer to seal the wood and prevent blotching.


How long after staining can I apply polyurethane to my project?

You should wait at least 24 hours after staining before applying polyurethane to your project. This allows the stain to fully dry and ensures a smooth and even finish when applying the polyurethane.