To prepare 100 ml of 1N HCl, you would need to dilute 8.4 ml of concentrated hydrochloric acid (37% w/w) with distilled water to a total volume of 100 ml.
To prepare 6N HCl from 1N HCl, you can dilute the 1N HCl by adding 6 times the volume of water to the 1N HCl solution. For example, mix 1 volume of 1N HCl with 6 volumes of water to get a final concentration of 6N HCl. Make sure to add acid to water slowly with stirring to avoid splashes and heat generation.
To prepare 100ml of 0.5N HCl solution, you would need to dilute concentrated HCl (37%) with distilled water in a volumetric flask. Measure 4.2ml of concentrated HCl, add it to the volumetric flask, and then dilute with distilled water to bring the total volume to 100ml. Mix well to ensure uniform concentration.
1M HCl means there is 1 mole of HCl in 1 liter of solution. To convert to 1N HCl, you need to consider the equivalent weight of HCl, which is its molecular weight as it is a monoprotic acid. So, in this case, 1M HCl is equivalent to 1N HCl.
To prepare Altman's acid fuchsin, dissolve 0.5g of basic fuchsin in 100mL of absolute ethanol. Then add 100mL of distilled water and 10mL of 1N hydrochloric acid. The solution should be filtered before use to remove any precipitates.
By dilution (1000x) with water: Take 1.0 mL 1.0N HCl and add up to 1000 mL with pure water.
To prepare 6N HCl from 1N HCl, you can dilute the 1N HCl by adding 6 times the volume of water to the 1N HCl solution. For example, mix 1 volume of 1N HCl with 6 volumes of water to get a final concentration of 6N HCl. Make sure to add acid to water slowly with stirring to avoid splashes and heat generation.
To prepare 100ml of 0.5N HCl solution, you would need to dilute concentrated HCl (37%) with distilled water in a volumetric flask. Measure 4.2ml of concentrated HCl, add it to the volumetric flask, and then dilute with distilled water to bring the total volume to 100ml. Mix well to ensure uniform concentration.
Ah, preparing a 0.02 M solution of HCl is a wonderful journey. Simply measure out the correct amount of hydrochloric acid and dilute it with water until you reach the desired concentration. Remember to handle chemicals with care and always wear appropriate safety gear. Happy experimenting, my friend!
1M HCl means there is 1 mole of HCl in 1 liter of solution. To convert to 1N HCl, you need to consider the equivalent weight of HCl, which is its molecular weight as it is a monoprotic acid. So, in this case, 1M HCl is equivalent to 1N HCl.
To prepare Altman's acid fuchsin, dissolve 0.5g of basic fuchsin in 100mL of absolute ethanol. Then add 100mL of distilled water and 10mL of 1N hydrochloric acid. The solution should be filtered before use to remove any precipitates.
By dilution (1000x) with water: Take 1.0 mL 1.0N HCl and add up to 1000 mL with pure water.
1N HCl is also 1M HCl because it is mono-protic. Therefore 36.5 g of HCl is required per liter or 3.65%. Simply take 100 g of 37% HCl and make up to the 1 liter mark on the volumetric flask. Check the value by titration against 1M NaOH. It should be perfect. If very slightly strong dilute very slightly (calculate) with water and re-standardize.
Oh, dude, it's simple! To make 2M HCl in 100ml from 36% HCl, you'd need to dilute the 36% HCl with water. Just mix 5.56ml of 36% HCl with 94.44ml of water, and voila, you've got yourself some 2M HCl. It's like making a fancy cocktail, but with chemicals!
1N HCL is the same as 1 Molar HCl. You take the # of H ions and multiply by the molarity to get the Normality. Usually you buy HCl in concentrated form which is 12 Molar or 12 Normal HCL. You need to dilute the concentrated HCl to get the reduced concentration. Use the formula Molarity Initial x Volume Initial = Molarity Final x Volume Final ex. 12 M HCL x 10 ml = 1 M x 120 ml. So take 10 ml of concentrated HCl and add enough water to make 120 ml. This will give you 120 ml of 1 M (which is 1N) HCl. Venkat Reddy
take the Mr of HCl to be 36.46. to prepare 1.0M we should take 36.46g and dilute to a litre to prepare 0.10M we should take 3.646g and dilute to a litre From density =mass/volume, we get volume=mass/density. So ideally we should take that volume and dilute to a litre. However we know that most conc HCl solution are not 100% HCl. thus we must multiply that volume by a factor 100/x for an HCl solution labelled x% Tauya Chigayo
To standardize 1N HCl (hydrochloric acid), you would typically use a primary standard base, such as sodium hydroxide (NaOH), of known concentration to titrate the HCl solution. By carefully titrating the HCl with the NaOH, you can determine the exact concentration of the HCl solution. This information can then be used to adjust the concentration of the HCl solution as needed to make it accurately 1N.
Take specific volume of 3N solution and increase the volume three times by adding distilled water.