answersLogoWhite

0

KCl is a salt having Ph 7, it is highly ionizable.yet a small leakage of ions from the reference electrode is needed, forming a conducting bridge to the glass electrode. A pH meter must thus not be used in moving liquids of low conductivity.

Sushant kumar

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Chemistry

How to Calibrate and Use a pH Meter?

A pH meter is normally something that an environmentalist or chemist would use, but some gardeners also make use of it. This meter is used to measure the acidity and alkalinity of a specific liquid. pH is the measure of how many hydrogen ions are present in a solution. Although the meter is very easy to use, it must be cleaned after each time it is used to get a clear reading.Before you can begin to calibrate your pH meter, you must make sure that the probe you use was kept in a storage solution or a solution with pH 4. If you do not do this, you need to let the probe sit for at least twenty four hours in distilled water. The meter must also be set on pH mode or this will be pointless. When it is set, you should rinse it off with distilled water. To help calibrate it, it will be placed into a solution of pH 7. But before you put it in, make sure that you shake off any distilled water or solution that was left on it.The probe should be left in the pH 7 solution for at least thirty seconds. This will let the meter stabilize completely so you can change the meter. You should now have the meter at a reading of pH 7. Now, you should take the probe out and rinse it off again. Then, put it into a solution of pH 4. Again, the meter will need a minute to stabilize. Then, you can change the meter to a pH 4 reading. At this point, the meter should be fully calibrated.You must rinse off the probe again with distilled water and shake off any remaining liquid to get the correct reading. Now, you can put the probe into your liquid sample for a clear reading. You need to let the pH reading settle for about a minute to be more precise. You can now get the pH reading from your sample. When you are completely finished using your probe, you should keep it in a storage solution or a solution of pH 4.


What happens when a silver spoon is kept in aqueous solution of copper sulphate?

When a silver spoon is kept in an aqueous solution of copper sulfate, a redox reaction takes place where silver displaces copper from the solution. As a result, silver ions in the solution get reduced and deposit copper onto the spoon. This process is known as displacement reaction, where a more reactive metal displaces a less reactive metal in a compound.


What would happen if a copper coin were kept immersed in a solution of silver nitrate write the word equation also?

copper is placed above the silver in the ractivity series which indicates that copper is more reactive than silver . when a copper coin is kept immersed in a solution of siler nitrate ,silver from its solution will deposit on copper coin . copper slowly displaces silver from the silver nitrate solution and the colour of solution changes from colourless to blue due to the formation of copper nitrate . the copper coin will disappear and silver will percipate out .


A copper coin was kept dipped in silver nitrate solution for a hours or dayswhat will happen to the colours of solution?

If a copper coin is dipped in silver nitrate solution for hours or days, the solution will likely turn blue due to the formation of copper(II) nitrate. This reaction occurs as copper from the coin reacts with the silver nitrate in the solution.


What is the control variable in titration?

In a titration experiment, the control variable is the volume of the titrant added to the analyte solution at each step. This volume should be kept consistent throughout the experiment to ensure accurate and reliable results.

Related Questions

What are two weather devices that must be kept outside?

a wind meter and a rainfall meter


If you add 240 g of sugar 50 mL of boiling water what will the solution be?

The result will be a sugar syrup with a concentration determined by how much the sugar dissolves in the boiling water. As the solution cools, the solubility of sugar decreases, which may result in sugar crystals forming unless the solution is kept hot or additional water is added.


Where is the perfect meter kept?

Its kept in a museum in Paris, inside a glass case with the temperature inside the case kept the constant.


Where is the correct si unit for meter is kept?

As long as the standard was a physical object, it was kept in Paris. But the meter is now defined in terms of the speed of light, so it can be reproduced to any arbitrary degree of precision in any sufficiently well-equipped laboratory, and no longer needs to be kept anywhere.


Why is mitochondria kept in sucrose solution when extracted from cell?

Mitochondria are kept in sucrose solution to maintain their osmotic balance and prevent them from swelling or shrinking due to changes in their external environment. The sucrose solution helps to stabilize the mitochondria and maintain their structural integrity during the extraction process.


For years to come Scrooge always keeps?

He always kept Christmas


Why do grapes shrink when kept in sugar solution?

osmosis takes place


How to Calibrate and Use a pH Meter?

A pH meter is normally something that an environmentalist or chemist would use, but some gardeners also make use of it. This meter is used to measure the acidity and alkalinity of a specific liquid. pH is the measure of how many hydrogen ions are present in a solution. Although the meter is very easy to use, it must be cleaned after each time it is used to get a clear reading.Before you can begin to calibrate your pH meter, you must make sure that the probe you use was kept in a storage solution or a solution with pH 4. If you do not do this, you need to let the probe sit for at least twenty four hours in distilled water. The meter must also be set on pH mode or this will be pointless. When it is set, you should rinse it off with distilled water. To help calibrate it, it will be placed into a solution of pH 7. But before you put it in, make sure that you shake off any distilled water or solution that was left on it.The probe should be left in the pH 7 solution for at least thirty seconds. This will let the meter stabilize completely so you can change the meter. You should now have the meter at a reading of pH 7. Now, you should take the probe out and rinse it off again. Then, put it into a solution of pH 4. Again, the meter will need a minute to stabilize. Then, you can change the meter to a pH 4 reading. At this point, the meter should be fully calibrated.You must rinse off the probe again with distilled water and shake off any remaining liquid to get the correct reading. Now, you can put the probe into your liquid sample for a clear reading. You need to let the pH reading settle for about a minute to be more precise. You can now get the pH reading from your sample. When you are completely finished using your probe, you should keep it in a storage solution or a solution of pH 4.


Where should dentures be kept?

Always in water


When returning from sea a green navigational buoys should be passed in what manner?

Always kept on portside


What kg one cubic meter methane gas?

The answer will depend on the pressure under which the gas is kept.


Why are fehling solution A and B kept separately?

fehling a is copper sulphate and fehling b is alkaline solution of sodium pottasium tartarate