0
What else can I help you with?
What is the frequency of household electricity?
In North America, it is 60 Hertz, and in Europe it is 50 hertz.
What is restriking voltage and recovery voltage?
Restriking Voltage : it is the transient voltage that exists during the arcing time. ( natural frequency kHz ). Recovery Voltage : it is the rms voltage after final arc extinction. ( normal frequency 50 or 60 Hz). both voltages appear between circuit breaker poles.
How do you calculate the rpm of a motor with a known number of poles and a frequency of 60 Hrtz?
A synchronous motor will spin at the system frequency. 60 Hz translates into 60*60 = 3600 direction changes per minute. If this is a two pole motor (one north and one south), it will spin 1 rotation per direction change. If it is a four pole motor (two north and two south), it will spin 1/2 rotation per direction change. If this is an induction motor, it will spin at a frequency slightly less than an equivalent synchronous motor; this frequency difference is referred to as slip.
What is the capacitive reactance of a 1 µF capacitor at a frequency of 60 Hz?
The capacitive reactance of a 1 µF capacitor at a frequency of 60 Hz is about 2700 ohms.
Why you use 400Hz frequency instead of 60Hz?
50 Hz has an edge over 60 Hz as it will have less skin effect and therefore line resistance will be less. Therefore, voltage drop as well as unwanted loss of energy in the line will be less. That means dip in supply voltage at user end will be less and efficiency will be more.AnswerThe difference in 'AC resistance' due to the effect of skin effect between 50/60 Hz is insignificant, just as the increase in inductive reactance, or the decrease in capacitive reactance is insignificant.The answer to your question is that the two frequencies simply resulted from the independent development of electricity distribution networks in different parts of the world, and there is no inherent advantage of one frequency of the other.Transformers for 60 Hz are smaller than for 50 Hz, assuming a given power rating. That is because the iron magnetic core can be reduced in size by 20% for 60 Hz, for the same peak magnetic flux density.
What is the difference between 50 Hertz and 61 Hertz?
The main difference between 50 Hz and 60 Hz is the frequency at which they operate. 50 Hz is a standard frequency used in many countries for electrical systems and appliances, while 60 Hz is commonly used in countries like the United States. The higher the frequency, the faster the alternating current cycles.
What is the Difference between the prime numbers 50 and 60?
None of them is prime as 50=2x52 and 60=22x3x5
If a bulb has 50 Hz frequency and it is apply at 60 Hz frequency voltage supply then it is glow or not?
If a bulb has 50 Hz frequency and it's supply is 60 Hz frequency, it will still glow, despite the allowance of 10 HZ frequency.
What are four equivalent expressions for 50-10?
60
What is the halfway point between 50 and 60?
The halfway point between 50 and 60 is (50 + 60) ÷ 2 = 55
What is the difference between 50 cal blow dart gun and 60 cal blow dart gun?
The 60 cal. has a bigger barrel.
What the frequency of a grid does?
50 herzes in INDIA and 60 hz in USA
What frequency rate is used for three phase operation?
Can be any frequency but is most likely to be the grid frequency - 50/60 Hz.
What is the industrial frequency?
Industrial frequency, as used in Communications, aka the ISM band, is the frequency of signals between 900Mhz to around 2.4Ghz of encoded, compressed, or analog signals... industrial frequency can also refer to the common local power grid frequency (usually 60 or 50 Hz)
What prime numbers are between 50 and 60?
prime numbers between 50 and 60: 53 & 59
What are the prime number there between 50 and 60?
The Prime Numbers between 50 and 60 are: 53 and 59.
What is the difference between km and miles?
A mile is 1.6 approx kilometres 30 miles 50 km 50 miles 80km 60 miles 100km
