0
What else can I help you with?
How carbon microphone works?
Carbon is a resistor, meaning it conducts electricity, but not very well.carbon microphone consists of two metal plates with a layer of small grains of carbon between. Each metal plate is attached to a wire which connects it to an audio receiver.A current runs from one plate through the carbon to the other plate. The carbon molecules normally resist it somewhat, lowering the power flow. When a sound wave pushes down on the top plate, however, it squeezes the carbon molecules more tightly between the two plates. This increases their conductivity, creating more electric current. As the plate moves up and down with the sound wave, the current increases and decreases, creating an electric wave in the shape of the sound wave.
What would make the plate of a vacuum tube glow bright red?
That bright red color is heat: infrared energy and visible light. The electrons gain kinetic energy as they accelerate away from the Cathode. As each electron is absorbed into the metal Plate, its kinetic energy becomes acoustic motion in the Plate's atoms - heat. (The plate is being hammered.)It is not normal for vacuum tube circuits to operate at high Plate temperatures that are this conspicuous. This circuit has an excessive product of Plate voltage times Plate current, and/or the vacuum tube Grids are biased incorrectly.One common technique for reducing this heating effect is to use a second Grid near the Plate that is biased much more positive than the Plate. This causes the electrons to decelerate between Grid 2 and the Plate - loosing most of their kinetic energy before absorbtion.
What protection must be provided when installing a cable in a notched stud or joist?
A metal plate, 1.59mm thick and measuring about 76mm x 41mm. Used to protect cable laid in notch in stud.
Does increasing the plate area of a capacitor increases the capacitance?
Yes. Increasing the plate area of a capacitor increases the capacitance. The equation of a simple plate capacitor is ...C = ere0(A/D)... where C is capacitance, er is dielectric constant (about 1, for a vacuum), e0 is electric constant (about 8.854 x 10-12 F m-1), A is area of overlap, and D is distance between the plates. (This is only a good estimate if D is small in comparison to A.) Looking at this, you can see that capacitance is proportional to plate area.
What is halm Jet press dry offset?
Halm Dry offset presses use a polymner plate (like a letter press) this would transfer the ink to the blanket instead of the subtractive metal plate used on wet ofset press's. The plate cylinders are magnetic to allow the plate to adhere to it. Some people use adhesive backed polymer plates to achieve the same result. All dry offset presses can be converted to wet offset but it is costly. You would need new plate cylinders, complete dampening systems, dampener recirculating tanks, water form arms, new oscillating bushings and new electronic controls for the additional water motors added to the press. These components are available after market for a lower cost.
Buick century license plate bulb replacement?
A Buick Century License Plate Bulb replacement can be done at home. You can go to any auto store to purchase the replacement part. Replacement can also be done at dealerships if needed.
What is the difference between a Bottom rail on a door and a Kick Plate on a door?
The bottom rail is the bottom section of the door itself. A kick plate is a metal plate, usually brass that is on the surface of the door.
How do you build a halo for home plate?
You have to get metal sticks and mound 4 around a plate and the get a metal ring and mound it on to the 4 metal sticks
What is the difference between a kick plate and a mop plate?
A kick plate is a metal or plastic plate installed at the bottom of a door to prevent damage from repeated kicking or impact. A mop plate, on the other hand, is a metal plate installed at the base of a wall to protect it from damage caused by mops and cleaning equipment.
Was the butt plate on a 1951 model 94 metal or plastic and where can you find one?
The butt plate on a 1951 Winchester Model 94 was typically made of metal. You may be able to find a replacement butt plate by searching online gun parts retailers, auction sites, or contacting gunsmiths who specialize in vintage firearms.
Can you bake a metal plate?
no
Where can I find a replacement quick release plate for my tripod?
You can find a replacement quick release plate for your tripod at camera stores, online retailers, or directly from the manufacturer's website.
Is there metal involed in plate tectonics?
No.
What is plate heat exchangers?
a plate heat exchanger is a metal plate which is will be in contact with another item eg air or another metal object to move heat from one to another
How do closet door magnets work to keep the door securely closed?
Closet door magnets work by using the magnetic force between the magnet and a metal plate on the door frame. When the door is closed, the magnet is attracted to the metal plate, creating a secure closure.
Whee can one purchase metal plate?
Metal plates can be found online at Metals Depot, Metal Plate, Harbor Steel, and American Plating Company. Metal plates can also be found on eBay and Amazon.
Is there a replacement stock for a Ruger 3 that does not have a crescent butt plate?
Yes
