In general all that can be said if the actual use of the wires is not stated is that one wire is the "supply" and the other wire is the "return" but there is no way to tell which is which without first learning more about how electricity works. The question does not say where the wires are being used. If they are on something using a battery or similar Direct Current (DC) supply then one wire may be connected to the positive side of the supply and the other wire may be connected to the negative side of the supply. The only safe and sure way to tell which wire is which is to measure the voltage with a voltmeter. If the wires are on something using a household Alternating Current (AC) supply, or a lower voltage via a "power supply unit" or a transformer, then one wire may be connected to the "Hot" or "Live" side of the supply and the other wire may be connected to the "Neutral" side of the supply. It is not easy to find out which one is the Neutral and which one is the "Hot" by just using a voltmeter set to measure AC - you have to know a bit more about electricity to find out which is which - but you should still be able to measure the AC voltage. If the wires are on something else, such feeding a loudspeaker from an amplifier, then one wire will be carrying the alternating sound signal to the speaker and the other wire would be the "neutral" returning the signal to the amplifier. IF YOU NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS. If you do this work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicator
to insure the circuit is, in fact, de-energized.
If both wires are black then the one with the writing is the neutral wire. If the two wires are black and white then the white one is the neutral.
If this is a home wiring question and the wires are black and white then black is Hot and white is Neutral. If you also have a red wire, it is the other hot wire, and either the black or the red wire to the white one would be 120 volts, and red to black would be 240 volts.
It is because the nec standard.
If both wires are black, the one that connects to your white wire is the one that should have little writing on it. Black to the plain black wire, white to the wire with writing.
Assuming the wires are the correct gauge for application and breaker you use black and white wires as hot. Put red electrical tape on each end of white wire and connect red and black to the breaker output and bare wire to ground lug in panel. At receptacle connect black and red to hot contacts and bare wire to ground lug.
1979 ford f150 there are 3 wires for the alternator one is black with red stripe one is red and the other is white which one goes where?"
The orange and green is the 12v feed from the auto shut down relay. The black and white wire is the wire the computer grounds.
speaker is black-, blue with brownish stripe + on power connector their are 4 wires ,2 of them are black,1 green,last is black with green stripe
Yellow: 12v memory Red: 12v ignition (switched) Orange: Dash Light Black: Radio Chassis Ground Blue: Power Antennae White: Left Front positive White/Black Stripe: Left Front Negative Green: LR positive Green/Black Stripe: LR negative Grey: RF positive Grey/Black Stripe: RF negative Violet: RR positive Violet/Black Stripe: RR negative
purple out of the 2 smaller wires black with white stripe is ground
There should be three wires attached to back of the alternator of a 66. You should have a black wire with a red stripe hooked to the GRD post, a black wire with a yellow stripe hooked to the BAT post and a white wire hooked to the FLD post. The black wire with the red stripe is the ground and splits off with one end bolting to the engine block on the same bolt that holds the negative battery cable to the block, the black wire with the yellow stripe goes to the hot side of the starter solenoid, and the white wire goes over to the F post on the voltage regulator.
If both wires are black then the one with the writing is the neutral wire. If the two wires are black and white then the white one is the neutral.
on your car the white w/blue stripe is 12 volt power you connect it to the yellow on the jvc stereo and the yellow w/ red stripe is the 12 volt accessory connect it to the red on the jvc stereo and connect the jvc stereo ground (black) to your cars black wire on the harness
the iat sensor is on the air intake on the drivers side of the engine. it has 5 wires on it. the red/black and black are the two iat wires. My 2005 Titan has two black wires, 1 tan wire, 1white wire, 1Red w/white stripe wire. Now what?
well try to find if one wire has a darker color copper than the other, this would help. or if one side of the wire coat has a white stripe on it, then the stripe indicates it's positive
"Typical" New Radio Wire Color Right Rear Spkr (-) Purple w/ Black Stripe Right Rear Spkr (+) Purple Right Front Spkr (-) Gray w/ Black Stripe Right Front Spkr (+) Gray Left Rear Spkr (-) Green w/ Black Stripe Left Rear Spkr (+) Green Left Front Spkr (- White w/ Black Stripe Left Front Spkr (+) White Ground Wire Black +12 Volt Ignition Red +12 Volt Battery Wire Yellow AMP REMOTE BLUE W/ WHITE STRIPE POWER ANTENNA BLUE
I broke open the unit and read the markings on the circuit board to figure this out. (I was tossing the DB135 in favor of a new Kenwood and needed to know how the stereo was wired. Yellow wire: Back up power (for clock/presets) Black: Ground Red: 12V source/ignition Green wires: Rear Left Grey wires: Front Right Purple wires: Right Rear White wires: Front Left Orange/White stripe: "ILL" (guessing illumination?) Blue/White stripe: Remote all speaker wires use the black striped one of same colorfor "negative"